Guides

Subdivision in the City of Salisbury: lot sizes and local rules

How land division works in the City of Salisbury: the Planning and Design Code zones and site areas, the airport and flood overlays around Edinburgh and Parafield, the Council's corner fence and driveway rules, who decides and the official fees.

Updated 11 min read

Want the answer for your address? Your report checks the zoning, lot size, constraints and costs for your block, in your inbox within 1–2 hours.

Check my block

In the City of Salisbury, the lot size you need to divide land is set by South Australia's statewide Planning and Design Code, not by a council scheme. The Code gives your land a zone, and that zone sets the minimum site area and frontage, either directly or through a Technical and Numeric Variation (TNV) mapped over your area. The official South Australian term is land division, and in most cases the Council's assessment manager decides it.

Salisbury then has its own mix of local constraints. RAAF Base Edinburgh and Parafield Airport bring airport height, lighting and noise overlays, low-lying land near the coast and creeks carries flood overlays, and the Council has its own rules on corner fences and driveway crossovers. This guide sets out those local rules alongside the Code figures. Figures are as at November 2026.

Which planning rules apply in the City of Salisbury

Every property in South Australia is covered by the Planning and Design Code, made under the Planning, Development and Infrastructure Act 2016. The Code is updated through Code Amendments, and the online Code shows the version in effect.

When the Code replaced the old Salisbury Development Plan, PlanSA published transition maps for the council area. Its 2020 transition table mapped the Residential Zone to the General Neighbourhood Zone (or the Suburban Neighbourhood Zone in the Salisbury Residential Policy Area), the Residential Hills Zone to the Hills Neighbourhood Zone, and Mawson Lakes residential land to the Housing Diversity Neighbourhood Zone. Zones have changed since through Code Amendments, so always check the current zone for your own lot.

How to find your lot's zone and TNV

  • SAPPA. On the South Australian Property and Planning Atlas, type your address into the search bar, open Layers, then Planning and Building, then expand Planning and Design Code. This shows the zone, the overlays and any Minimum Site Area or Minimum Frontage TNV.
  • The online Code. Enter a property in the online Planning and Design Code to see every policy that applies to it.
  • The Council. The City of Salisbury's planning team can talk you through what applies to a specific lot.

Then check your certificate of title for the lot's area and for any easements that could limit where a new boundary goes.

Site areas for common Salisbury zones

Zone Minimum site area Minimum frontage
General Neighbourhood Detached dwelling 300 m², exclusive of any battle-axe handle. Semi-detached 300 m². Row dwelling 250 m². Group dwelling or residential flat building 300 m² average Detached 9 m, or 5 m on a battle-axe site. Semi-detached 9 m. Row 7 m (averaged). Group or residential flat building 15 m
Suburban Neighbourhood Set by the Minimum Site Area TNV. PlanSA's guide says generally 350 to 800 m² Set by the Minimum Frontage TNV
Housing Diversity Neighbourhood Set by the zone or a TNV; check SAPPA Set by the zone or a TNV; check SAPPA
Hills Neighbourhood Set by the Minimum Site Area TNV Set by TNV

These are the zones' deemed-to-satisfy or designated performance feature (DTS/DPF) figures. PlanSA's guide describes the General Neighbourhood Zone as encouraging "low-rise, low and medium-density housing", and the Housing Diversity Neighbourhood Zone as envisaging "medium density housing". Newer estates can sit in other zones, such as the Master Planned Neighbourhood Zone, which the guide says envisages "a new or expanding community with a diverse range of housing". Where a zone relies on a TNV, read the figure for your own lot on SAPPA.

In the General Neighbourhood Zone, the standalone deemed-to-satisfy route for land division is limited to no more than five additional allotments of at least 300 m² and 9 m frontage, on fairly flat land with no regulated trees nearby, no new public road and no battle-axe allotments. A layout that falls outside it, including a battle-axe layout, is assessed on its merits. Missing a figure is not an automatic refusal, but it is not an entitlement either. For the full zone rules see our guide to the minimum lot size for subdivision in SA, and for rear lots see battle-axe subdivision explained.

Local rules that change the answer in Salisbury

RAAF Base Edinburgh and Parafield Airport

Two airfields shape development across much of the council area.

  • Defence Aviation Area. The City of Salisbury says the Defence Aviation Area regulations "apply as far as 15 kilometres from the RAAF Base Edinburgh". They cover structures, vegetation and exhaust gas plumes, and may require referral to Defence. The Council suggests checking the Defence Aviation Area map to see if a property is affected. PlanSA's guide says the Code's Defence Aviation Area Overlay manages the impact of buildings on the operational and safety requirements of these areas, and reflects the height limits around Edinburgh.
  • Airport Building Heights (Regulated) Overlay. It manages potential impacts of buildings on the operation and safety of certified airfields and airports.
  • Building Near Airfields Overlay. It manages lighting and bird attraction near airfields. A 2024 Council Assessment Panel report for land in Edinburgh also lists a Code concept plan, Concept Plan 81, covering Edinburgh Defence Airfield lighting constraints.
  • Aircraft Noise Exposure Overlay. It aims to ensure that development sensitive to aircraft noise is designed and located to manage noise intrusion and land use conflict.

Height limits mostly matter for taller buildings, but these overlays can still bring extra tests or a referral. Check SAPPA to see which apply to your lot.

Flooding

The Code has three flood overlays: Hazards (Flooding), Hazards (Flooding – General) and Hazards (Flooding – Evidence Required). PlanSA's guide says the Hazards (Flooding) Overlay seeks to limit the intensification of development in higher-risk flood areas. A 2024 Council Assessment Panel report for a land division in Globe Derby Park listed both the Hazards (Flooding) and Hazards (Flooding – General) overlays over that site.

The 2023 Flooding Hazards Mapping Update Code Amendment named Salisbury among the areas where the Evidence Required overlay was to be reduced, based on newer flood mapping, and the Minister for Planning adopted it in March 2024.

Proposed change. The draft State-Wide Flood Hazard Code Amendment was released on 21 May 2026 and was open for consultation until 13 August 2026. It would update flood mapping using new flood studies and improve the planning rules for development. PlanSA says it would remove flood-related planning requirements from more than 280,000 properties. It is a proposal only, and an engagement report goes to the State Planning Commission and the Minister for Planning before any decision.

Heritage and character

State and Local Heritage Places, Historic Areas and Character Areas are all shown as overlays in the Code. PlanSA's guide says the Local Heritage Place Overlay seeks to ensure development maintains the heritage and cultural values of those places. A listing does not automatically rule out a land division, but it shapes the assessment. Check SAPPA for your lot, and see heritage and subdivision.

Corner blocks and fences

The City of Salisbury requires Council approval for "a fence over 1 metre in height within 6 metres of a road intersection", except where a 4 x 4 metre corner cut-off has been provided. Approval is also needed for a fence taller than 2.1 m, a masonry fence taller than 1 m, or where a retaining wall and fence together exceed 2.1 m, measured from the lowest side of the ground. If a corner lot is being divided, new boundary fences near the intersection need to fit these rules. See corner block subdivision.

Driveway crossovers

A battle-axe or side-by-side layout usually needs a new or relocated driveway crossover. The Council says that where a new driveway is shown on an approved development application, approval under section 221 of the Local Government Act 1999 is granted automatically. Otherwise you apply separately, and assessment may take up to 10 business days. Work must follow the Council's standard details (SD-201 to SD-203), and either you or your contractor must hold $20 million public liability insurance. You can ask the Council to do the work for a fee, allowing up to four weeks.

Civil works and trees

Any roads, stormwater or other civil works built as part of a development must meet the Council's Infrastructure Guidelines. The Council says these are under review and asks applicants to contact Development Engineering Services early in the design process.

The Council's 2026/27 fee for the planning assessment of a regulated or significant tree removal is $129. A tree near a proposed boundary or driveway can change the layout, and in the General Neighbourhood Zone, regulated trees on or within 20 m of the land rule out the standalone deemed-to-satisfy route.

How land division approval works

You need land division consent and planning consent, which together form your development approval, lodged through the PlanSA portal.

  • Who decides. PlanSA says an assessment manager can grant land division consent for all development, except where the State Planning Commission or the Minister for Planning is the authority. The Commission delegates its decisions to the State Commission Assessment Panel (SCAP). Since 2025 the Commission's Land Division Assessment Panel can assess large land divisions of 20 or more allotments, and applications where councils have not met statutory assessment timeframes.
  • Certificate. After approval you apply for the Land Division Certificate of Approval, which PlanSA says "is issued by Planning and Land Use Services". The land division fee and open space contribution are paid at this stage.
  • New titles. Land Services SA deposits the plan and issues new titles.

Under the Planning, Development and Infrastructure (Fees) Notice 2026, applying from 1 July 2026, the land division fee is $210 where no more than four additional allotments and no public road are created, the certificate of approval is $1,229, and the open space contribution in Greater Adelaide is $10,166 per new allotment of 1 hectare or less. SA Water's 2026-27 augmentation charges for Greater Adelaide infill residential development are $4,017 for water and $4,017 for wastewater per additional allotment (greenfield locations are charged a higher rate; apartments and community housing are exempt). For every step and fee, see how to subdivide land in South Australia, and for an estimate of total costs, try our subdivision cost calculator.

Free design review. The Council offers a free design review before or after you lodge, and says before lodgement is preferable. Feedback typically takes about 10 business days.

Contacting the City of Salisbury

The City of Salisbury can be reached on (08) 8406 8222 or at city@salisbury.sa.gov.au. The Customer Centre is at the Salisbury Community Hub, 34 Church Street, Salisbury, open 8.30am to 5.00pm Monday to Friday, excluding public holidays. The postal address is PO Box 8, Salisbury SA 5108.

Check your own block

A Subdivision Checker report applies these rules to one address: planning and zoning, heritage, environment, contamination, bushfire, flood, servicing and access, measured lot geometry and concept subdivision design options, plus indicative cost ranges labelled as estimates. It is a starting point, not a substitute for advice from a licensed surveyor or town planner. To see how the checks are set out, view our sample report, or order a report for your address.

Frequently asked questions

What is the minimum lot size for subdivision in the City of Salisbury?

There is no single council-wide figure. South Australia's Planning and Design Code sets the minimum site area and frontage by zone. In the General Neighbourhood Zone the deemed-to-satisfy figure for a detached dwelling is 300 m² with a 9 m frontage, exclusive of any battle-axe handle. Zones such as Suburban Neighbourhood and Hills Neighbourhood take their figures from a Minimum Site Area Technical and Numeric Variation (TNV) mapped over each area, so the figure can change from street to street.

How do I find the zone for my property in Salisbury?

Search your address on the South Australian Property and Planning Atlas (SAPPA), open Layers, then Planning and Building, then Planning and Design Code. This shows the zone, the overlays and any Minimum Site Area or Minimum Frontage TNV. The online Planning and Design Code also lets you enter a property and see the policies that apply. The City of Salisbury's planning team can help on (08) 8406 8222.

Does the City of Salisbury approve land divisions?

Usually the Council's assessment manager is the relevant authority for land division consent, except where the State Planning Commission or the Minister for Planning is the authority. The Commission delegates its decisions to the State Commission Assessment Panel (SCAP). Once development approval is granted, Planning and Land Use Services, not the Council, issues the Land Division Certificate of Approval, and Land Services SA deposits the plan and issues new titles.

Does being near RAAF Base Edinburgh or Parafield Airport affect subdivision?

It can. The Council says the Defence Aviation Area regulations apply as far as 15 kilometres from RAAF Base Edinburgh, covering structures, vegetation and exhaust plumes, and may require referral to Defence. The Planning and Design Code also has Airport Building Heights (Regulated), Building Near Airfields and Aircraft Noise Exposure overlays. Subdivision is not ruled out, but these overlays add tests. A licensed surveyor or town planner can advise on a specific lot.

What is the corner cut-off rule for fences in Salisbury?

The City of Salisbury says Council approval is needed for a fence over 1 metre in height within 6 metres of a road intersection, except where a 4 x 4 metre corner cut-off has been provided. Approval is also needed for any fence taller than 2.1 metres, a masonry fence taller than 1 metre, or where a retaining wall and fence together exceed 2.1 metres.

Is flood mapping changing in Salisbury?

Changes are proposed but not in force. The draft State-Wide Flood Hazard Code Amendment was open for consultation from 21 May to 13 August 2026 and would update flood mapping and rules across South Australia. An engagement report goes to the State Planning Commission and the Minister for Planning. Until a decision is made, the flood overlays currently shown on SAPPA apply.

Sources

This guide is general information only, current at November 2026. Rules, fees and maps change, and every block is different. Speak to a licensed surveyor or town planner about your property.

More subdivision guides

See what applies to your block.

A Subdivision Checker report works through the lot size test, constraints, approval pathway and costs for your address, with every source listed. Full report $199, or a $39 Snapshot.