Guides

Minimum lot size for subdivision in WA and Perth: R-Codes explained

How the R-Codes set minimum and average site areas for each density code in WA, the R10 to R60 figures, battle-axe and split coding rules, how to find your lot's R-Code, and the draft changes now out for comment.

Updated 14 min read

Want the answer for your address? Your report checks the zoning, lot size, constraints and costs for your block, in your inbox within 1–2 hours.

Check my block

In Western Australia, the minimum lot size for subdivision is set by the Residential Design Codes (R-Codes), a planning code made under the Planning and Development Act 2005; earlier editions were titled State Planning Policy 7.3. Table D of the R-Codes Volume 1 sets a minimum and an average site area per dwelling for each density code, such as R20 or R30. Your council's local planning scheme map gives your lot its code.

So "how big does my block need to be to subdivide in Perth?" has a two-step answer: find your lot's R-Code, then compare the lot with the Table D figures for that code. At R20, for example, the minimum is 350 m² and the average is 450 m², so two lots generally need at least 900 m² between them. This guide sets out the Table D figures, battle-axe and split coding rules, how approval works, and the draft changes now out for comment. Figures are as at November 2026.

R-Codes subdivision table: minimum and average site areas (as at November 2026)

These figures are from Table D (Site area requirements) of the Residential Design Codes Volume 1, Version 3, published 10 April 2026. They apply to single houses and grouped dwellings.

R-Code Minimum site area per dwelling (m²) Average site area per dwelling (m²) Minimum lot area, rear battle-axe (m²)* Minimum frontage (m)*
R10 875 1,000 925 20
R12.5 700 800 762.5 17
R15 580 666 655 12
R17.5 500 571 587.5 12
R20 350 450 450 10
R25 300 350 425 8
R30 260 300 410 –
R35 220 260 395 –
R40 180 220 380 –
R50 160 180 160 –
R60 120 150 120 –

*Table D says the minimum lot area/rear battle-axe and minimum frontage columns apply only to single houses. A dash means not applicable.

Multiple dwellings (apartments) have their own average site areas in Table D, and the department says Volume 1 covers multiple dwellings at R60 and below. Always check the current table before relying on a figure.

How the minimum and average tests work

Each code sets two separate tests, and a subdivision has to pass both:

  • Minimum site area: the smallest any one lot can be.
  • Average site area: the total site area divided by the number of lots.

A block can pass the minimum and still fail the average. Some worked examples, on area alone:

  • R20: two lots of 350 m² each pass the minimum, but the average must be 450 m², so two lots generally need at least 900 m².
  • R30: the minimum is 260 m² and the average 300 m², so two lots generally need at least 600 m².

For a single house on a rear battle-axe lot, the separate minimum lot area column also applies, and it is higher than the minimum site area at R10 to R40. At R30, for example, a rear battle-axe lot for a single house needs 410 m², against a 260 m² minimum site area.

The five per cent variation

The R-Codes let the Western Australian Planning Commission (WAPC), in consultation with the local government, approve lots up to five per cent smaller than the Table D minimum or average. The variation must achieve one or more listed outcomes, such as protecting an environmental or heritage feature, retaining a significant element of the streetscape, providing frontage to more than one public street, or overcoming a special limitation of the land's size or shape. The WAPC's Operational Policy 2.2 says the minimum lot size variation applies to only one lot in the subdivision. It is a discretion, not an entitlement.

Corner lots

When checking compliance with Table D, up to 20 m² of a corner truncation to a public street can be added to the area of the adjoining lot.

Battle-axe lots: does the access leg count?

A battle-axe (rear) lot reaches the street through a narrow access leg. Under the R-Codes:

  • R40 and below: the access leg can be counted in the rear lot's site area, but it can contribute no more than 20 per cent of the site area required by Table D.
  • R50 and above: the access leg and associated truncations are excluded, to give an effective lot area.
  • Next to a right-of-way or reserve: where a battle-axe lot abuts a right-of-way or certain reserves, half the width of that right-of-way or reserve, up to 2 m deep, may be added to its site area.

Operational Policy 2.2 adds the WAPC's own rules:

  • The battle-axe configuration is not favoured, and direct street frontage, or street and rear laneway access, is preferred.
  • The WAPC will not permit reductions in the minimum or average lot sizes for battle-axe lots.
  • The access leg should be at least 4 m wide at R2 to R40, or 3.6 m at R50 and higher.
  • Arrangements with more than two access legs will not be accepted except in exceptional circumstances.
  • Where battle-axe subdivision would seriously threaten the character of an established area, local governments may use density controls, local planning policy or local development plans.

For layouts, driveways and common issues, see battle-axe subdivision explained.

Split codings such as R20/R40

Some scheme maps show two codes for the same land, such as R20/R40. This is called a split or dual density code. The lower code is the starting point, and the local planning scheme sets out when the higher code can be used.

The City of Joondalup's Local Planning Scheme No. 3 is an example. Clause 26(4) says that where a dual density code applies as shown on the Scheme Map, the base R20 code applies unless the higher code is found acceptable having regard to the scheme's criteria. Those criteria, inserted by Amendment No. 5 (gazetted 29 January 2021), include a minimum frontage of 9 m at the primary street setback for single and grouped dwellings, or 6 m for grouped dwellings on corner lots with frontage to two streets and rear common property access.

Other councils set different conditions, so read the clause in your own scheme. Operational Policy 2.2 also says that, where the WAPC considers an average lot size variation of more than five per cent, the variation applies only to the base coding of dual-coded land.

Can I subdivide my block in Perth?

Subdividing land in Perth starts with three questions:

  1. What is the lot's R-Code? This comes from the local planning scheme map.
  2. Does the lot meet both Table D tests for the number of lots you have in mind, and the frontage and battle-axe rules?
  3. Does anything else get in the way? Access, the existing house, servicing, bushfire, heritage and title restrictions can all change the answer.

Only the WAPC can approve a subdivision, and meeting Table D does not guarantee approval for any particular block.

Local rules by council

Each council's local planning scheme sets the density codes for its area and can add its own rules, such as criteria for using the higher code on split-coded land, laneway requirements and heritage areas. Our council guides set these out with the official sources:

How to find your lot's R-Code

  • PlanWA. The Department of Planning, Lands and Heritage's PlanWA mapping tool covers local planning schemes, region schemes and heritage information across Western Australia, and the department says its data is updated weekly.
  • Your council's local planning scheme maps. Your council can confirm the scheme map for your lot. The City of Vincent, for example, says the R-Code appears after the zone name on its online maps, so "Residential R30" means an R30 density coding.
  • The scheme text. Check it for split coding clauses and any local provisions, and your certificate of title for the lot area, easements and covenants.

The WAPC subdivision approval process

In WA the decision-maker is the Western Australian Planning Commission, not your council. In outline:

  1. Apply on Form 1A (Application for Approval of Freehold, survey-strata, leasehold (survey-strata) or community titles (land) scheme subdivision). The preferred lodgement method is the Planning Online portal. All subdivision plans must be based on an accurate and up-to-date feature survey.
  2. Referral. The WAPC refers the proposal to the local government and any affected public authority or utility services provider, which have 42 days to respond with objections or recommendations.
  3. Decision. The WAPC is to take no more than 90 days to decide, unless the applicant and the WAPC agree otherwise in writing. It can approve, approve with conditions, or refuse. The applicant can ask the WAPC to reconsider within 28 days of the decision, or seek review by the State Administrative Tribunal within 28 days.
  4. Conditions and clearances. The applicant fulfils the conditions of approval in consultation with the relevant local government, public body or private utility.
  5. Endorsement. Within 3 years (5 lots or fewer) or 4 years (more than 5 lots), the plan goes to the WAPC for endorsement on Form 1C. The WAPC endorses a plan certified correct by Landgate once it matches the approval and the conditions are met.
  6. New titles. Applications for title must be made through Landgate within two years of the WAPC endorsement date.

WAPC fees from 1 July 2026, under the Planning and Development (Fees) Amendment Notice 2026: for a subdivision into 100 or fewer lots, the application fee is $3,837 plus $85 per lot, and endorsement of the plan is $719 plus $8 per lot.

In WA the professional who surveys the new lots is a licensed surveyor. Under the Licensed Surveyors Act 1909, only a licensed surveyor holding a practising certificate can make an authorised survey, which includes surveys under the Transfer of Land Act 1893, and licences are overseen by the Land Surveyors Licensing Board. A town planner can help where the proposal needs planning justification.

For each step, timeframes and the other fees, see How to subdivide land in Western Australia.

Draft R-Codes changes (proposed, not in force)

The State Government released draft R-Codes for public comment on 24 October 2026. The Government's media statement says the package would see average lot sizes for R10 to R25 scrapped in Perth and Peel, and estimates that more than 70,000 existing residential properties would become eligible to subdivide.

The Department of Planning, Lands and Heritage is also seeking comment on repealing Operational Policy 2.2, with its remaining provisions moved into a draft Operational Policy Subdivision of Land and the R-Codes.

  • Status: draft only. Applications continue to be assessed under the current framework.
  • Comment closes: 5.00pm (AWST), Friday 26 February 2027, on the department's Have Your Say website.
  • Timing: subject to consultation and approval, the department expects amendments to begin coming into effect later in 2027.

Until any change commences, the Table D figures above apply. For more, see our news article on the draft R-Codes consultation.

What else decides whether a block can be split

Meeting Table D is only the first test.

Frontage. Table D sets a minimum frontage for single houses at R10 to R25, from 20 m at R10 to 8 m at R25, and 10 m at R20. Operational Policy 2.2 says the lot size and frontage requirements of the relevant R-Code form the basis for subdividing residential land.

Water Corporation servicing and contributions. Operational Policy 2.2 is based on the mandatory provision of reticulated sewerage to all new residential subdivisions, unless exemptions apply. Water Corporation's standard infrastructure contributions for 1 July 2026 to 30 June 2027 are $2,756 for water and $5,121 for wastewater per lot, plus $41 for drainage in urban declared drainage areas of the Perth metropolitan area (not for strata subdivisions). They are not subject to GST, and some areas also carry special contributions.

Bushfire prone areas. The Fire and Emergency Services Commissioner designates bush fire prone areas on the Map of Bush Fire Prone Areas. DFES says designation can trigger State Planning Policy 3.7 and the Planning for Bushfire Guidelines where a proposal increases development intensity or bushfire risk. The current map took effect on 13 December 2025.

Heritage. The State Register of Heritage Places is kept under the Heritage Act 2018, and councils keep a local Heritage List under their local planning schemes. Search listings on inHerit. For Aboriginal heritage, the Aboriginal Heritage Act 1972 applies, and the Aboriginal Cultural Heritage Inquiry System (ACHIS) shows known Aboriginal heritage.

Operational Policy 2.2 (Residential Subdivision). This WAPC policy, operational from 31 May 2024, sits alongside the R-Codes in assessing residential subdivision, covering lot size variations, battle-axe lots, existing dwellings and servicing. It is proposed for repeal, as above, but remains in effect for now.

Costs. For every WA government fee added up for a two-lot and three-lot split, see our WA subdivision cost guide. For a fuller picture across Australia, see how much does it cost to subdivide in Australia. To compare WA with other states, see Minimum lot size for subdivision in every Australian state.

Check your own block

A Subdivision Checker report applies these rules to one address: planning and zoning, heritage, environment, contamination, bushfire, flood, servicing and access, measured lot geometry and concept subdivision design options, plus indicative cost ranges labelled as estimates. It is a starting point, not a substitute for advice from a licensed surveyor or town planner. To see how the checks are set out, view our sample report, or order a report for your address.

Frequently asked questions

What is the minimum lot size for subdivision in WA?

It depends on the density code (R-Code) your local planning scheme gives the land. Table D of the Residential Design Codes Volume 1 sets a minimum and an average site area per dwelling for each code. For single houses and grouped dwellings, the minimum is 875 m² at R10, 350 m² at R20, 260 m² at R30 and 180 m² at R40, and each code also has a higher average that the whole subdivision must meet.

What is the minimum lot size for R20?

Table D sets a minimum site area of 350 m² and an average site area of 450 m² per dwelling at R20. Because both tests apply, two lots generally need at least 900 m² of site area between them. For a single house on a rear battle-axe lot, Table D sets a minimum lot area of 450 m², and the minimum frontage for a single house at R20 is 10 m.

What lot size do I need to subdivide an R30 block?

At R30, Table D sets a minimum site area of 260 m² and an average of 300 m² per dwelling, so two lots generally need at least 600 m² of site area between them. A single house on a rear battle-axe lot needs a minimum lot area of 410 m². Area is only the first test: access, the existing house, servicing and other constraints must also work, and a licensed surveyor or town planner can advise on your site.

Does the battle-axe access leg count toward lot area in WA?

In areas coded R40 and below, the R-Codes let the access leg count toward a rear battle-axe lot's site area, but the leg can contribute no more than 20 per cent of the site area required by Table D. In areas coded R50 and above, the access leg is excluded. Operational Policy 2.2 also says the leg should be at least 4 m wide at R2 to R40, or 3.6 m at R50 and above.

What does a split code like R20/R40 mean?

A split or dual code means the local planning scheme map shows two density codes for the land. The scheme says when the higher code can be used. In the City of Joondalup, for example, the base R20 code applies unless the higher code is found acceptable against criteria in the scheme, such as a minimum 9 m frontage for single and grouped dwellings. Other councils set their own criteria.

Are WA minimum lot sizes changing?

Changes are proposed but not in force. The draft R-Codes released on 24 October 2026 propose scrapping average lot sizes for R10 to R25 in Perth and Peel. Submissions close at 5.00pm (AWST) on Friday 26 February 2027, and the department expects amendments to begin coming into effect later in 2027, subject to consultation and approval. Until then, the current Table D applies.

Sources

This guide is general information only, current at November 2026. Rules, fees and maps change, and every block is different. Speak to a licensed surveyor or town planner about your property.

More subdivision guides

See what applies to your block.

A Subdivision Checker report works through the lot size test, constraints, approval pathway and costs for your address, with every source listed. Full report $199, or a $39 Snapshot.