A corner block has frontage to two streets. That one feature changes how a subdivision can be laid out. Instead of squeezing a rear lot behind the house with a long driveway, a corner block can often be split so that each new lot faces its own street.
It is not automatic, though. Corner blocks come with their own rules: truncations where the streets meet, setbacks from the second street and limits on fences and walls near the corner so drivers can see. This guide explains how those rules work and where each state publishes them.
Why a corner block is different
On a typical mid-street block, a second lot usually means a rear lot reached by an access leg, often called a battle-axe lot. On a corner block, the second street gives the new lot a frontage of its own. That can mean:
- no access leg, so more of the land is usable
- each home has its own street address and driveway
- the existing house may be able to stay, with the new lot facing the side street
Is a corner block easier to subdivide? Often it can be, because each new lot can face its own street, so no access leg is needed. But a corner block still has to meet the minimum lot size, frontage and other rules for its zone, and the truncation, setbacks and sight line rules can reduce the usable area.
Corner truncations
What is a corner truncation? A truncation is the corner of a lot cut off on an angle where two streets meet, so the corner becomes part of the road reserve. It keeps sight lines clear for drivers and pedestrians. Whether a truncation is needed, and its size, is set by the council or the approving authority.
A truncation can matter on a block that is close to the minimum lot size, because some or all of the land in the truncation may not count towards the new lot. In WA, for example, the R-Codes let up to 20 m2 of a corner truncation be counted in the lot area, but Operational Policy 2.2 excludes it when a corner lot variation is sought. Your surveyor will show any existing or required truncation on the plan of subdivision.
Sight lines, fences and driveways near the corner
States and councils limit what can be built close to an intersection so that drivers can see. A few published examples:
- WA: the R-Codes' deemed-to-comply provisions require walls, fences and other structures to be truncated or reduced to no higher than 0.75 m within 1.5 m of driveways and intersecting streets, and driveways to be no closer than 6 m to a street corner, as required under AS 2890.1.
- SA: the City of Salisbury says approval is needed for a fence over 1 metre high within 6 metres of a road intersection, except where a 4 x 4 metre corner cut-off has been provided. PlanSA's Draft Design Standard 1 for land divisions proposes that driveways on corner allotments be at least 6 metres from the tangent point of the kerb return. That standard was released as a draft for consultation in 2026 and is not yet in force.
- NSW: Camden Council's development control plan sets a 2 m setback from the secondary street on a corner lot, with an objective to maintain sight lines for the safety of pedestrians and vehicles.
These rules affect where the driveway for each new lot can go, which can decide whether a corner split works on a small block.
The rules by state
Western Australia
Lot sizes in WA come from the Residential Design Codes (R-Codes). The current Volume 1 is Version 3, published on 10 April 2026. Draft changes to the R-Codes are out for public comment from 24 October 2026 to 26 February 2027 and do not yet apply.
Does WA give corner lots a lot size concession? There is no general corner lot reduction in Table D of the R-Codes. The WAPC's Operational Policy 2.2 can allow the average lot size to be varied by more than five per cent for a corner lot with frontage to two different streets, but only where a single coding of R10 to R35 applies, all proposed lots meet the Table D minimum lot size and frontage, and each new home can have its primary frontage to a different street. For that variation, any corner truncation is excluded when the minimum lot size is calculated. Outside that variation, the R-Codes allow up to 20 m2 of a corner truncation to be counted in the area of the adjoining lot.
Operational Policy 2.2 also allows the area of one lot to be reduced by no more than five per cent of the minimum lot size, in limited cases. The WAPC's page for the policy says comment is being sought on a proposed repeal, linked to the R-Codes review, so check its status before relying on it.
The R-Codes also deal with setbacks on corner lots:
- buildings are set back from the secondary street in line with Table B
- garages and carports can be set back 1.5 m from a secondary street
- where a single house results from the subdivision of an original corner lot and faces the original secondary street, the street setback may be reduced to 2.5 m, or 1.5 m to a porch, balcony or verandah, in areas coded R15 or higher
Where the existing house is kept and access is by a battle-axe leg or communal street, Operational Policy 2.2 expects adequate space for the car parking that the R-Codes require.
Victoria
Victoria's residential standards set street setbacks for corner sites. Under Clause 55.02-1 (Standard B2-1), described in the Department of Transport and Planning's Townhouse and Low-Rise Code guidelines, the side street setback for a corner site is linked to neighbouring buildings, with a cap of 3 metres for front walls and 2 metres for side walls, whichever is the lesser. For a single dwelling under Clause 54.02-1 (Standard A2-1), either street frontage may be selected as the front setback on a corner lot.
Some Victorian planning schemes set a minimum subdivision area in the schedule to the zone, so similar corner blocks can be treated differently from one council to the next.
Queensland
In Queensland, lot sizes and frontages are set by each council's planning scheme. Brisbane City Council's subdivision fact sheet gives a minimum of 450 m2 for a front lot and 600 m2 for a rear lot in the low density residential zone, subject to minimum frontage, average width and development rectangle requirements. Smaller "small lot" sizes are possible in some locations, and Brisbane changed its lot size rules in September 2026 (see our Brisbane subdivision guide), so check the current City Plan. On a corner block where each new lot has its own street frontage, neither lot may need to be a rear lot, so ask council which minimum applies.
New South Wales
In NSW, minimum lot sizes are usually set in the council's local environmental plan, and corner lot controls such as secondary street setbacks are usually in the council's development control plan. Camden's plan, for example, treats the shorter of the two frontages as the primary street frontage.
South Australia
Land division in SA is assessed under the Planning and Design Code. Council rules near intersections, such as the 4 x 4 metre corner cut-off used for fencing in Salisbury, show how a corner can affect the usable area.
ACT, Tasmania and the Northern Territory
- ACT: the Territory Planning Authority's Advisory Note 17 on corner blocks says reduced setbacks apply only to the street frontage nominated as the secondary street frontage. The note is guidance for single dwellings, not a statutory rule.
- Tasmania: the State Planning Office's residential zones fact sheet gives a 450 m2 minimum lot size in the General Residential Zone.
- Northern Territory: Part 6 of the NT Planning Scheme 2020 sets minimum lot sizes by zone, and minimum road frontages for smaller residential lots.
Corner split or battle-axe split?
Is a corner split better than a battle-axe split? Neither is better in every case. A corner split gives each lot its own street frontage, while a battle-axe lot needs an access leg and can face a higher minimum lot size. In Brisbane, for example, the council's subdivision fact sheet gives a low density residential minimum of 450 m2 for a front lot and 600 m2 for a rear lot, with smaller lots possible in some locations.
The way the existing house sits on the block often decides the layout. A house in the middle of a corner block may need to be removed, or a shed or carport demolished, to make room for a second lot facing the side street. Our guide to battle-axe subdivision explains the rear lot option, and our guide to minimum lot sizes by state covers the numbers.
Getting advice
A licensed surveyor can measure the block, confirm any truncation and show how the lots could be laid out. A town planner can confirm which codes and policies apply to your corner block.
If you would like a first look at the measured frontages and design options for your address, you can check your block with Subdivision Checker.
Sources
- Operational Policy 2.2: Residential Subdivision (WAPC publication page)
- Design standards in land division assessment fact sheet (PlanSA)
- Residential Design Codes Volume 1, Version 3, 10 April 2026 (WA Government)
- Operational Policy 2.2 Residential Subdivision, 31 May 2024 (WA Planning Commission)
- Townhouse and Low-Rise Code Guidelines, May 2025 (Victorian Department of Transport and Planning)
- One dwelling and small second dwelling guidelines, September 2025 (Victorian Department of Transport and Planning)
- Subdividing land fact sheet (Brisbane City Council)
- Setbacks, Camden Development Control Plan (Camden Council)
- Fencing (City of Salisbury)
- Draft Design Standard 1: Engineering Requirements for Land Divisions (PlanSA)
- Advisory Note 17: Corner blocks (ACT Territory Planning Authority)
- Part 6 Subdivision and consolidation requirements, NT Planning Scheme 2020 (NT Government)
- Tasmanian Planning Scheme residential zones fact sheet (State Planning Office)
This guide is general information only. For advice on your property, speak with a licensed surveyor or town planner in your state.
