Guides

Subdividing in Canberra: ACT block size rules for RZ1 and RZ2

How subdivision and unit titling work in Canberra under the Territory Plan 2023, the RZ1 and RZ2 block size rules, the status of the Missing Middle reforms, who approves, and the Crown lease steps.

Updated 14 min read

Want the answer for your address? Your report checks the zoning, lot size, constraints and costs for your block, in your inbox within 1–2 hours.

Check my block

Subdivision is a permissible use in Canberra's two main house-block zones, RZ1 Suburban and RZ2 Suburban Density, but every proposal needs development approval from the Territory Planning Authority, and whether a particular block can be split depends on its size, shape, Crown lease and constraints. Since 1 July 2026, each new block needs at least 350 m² in RZ1 and 300 m² in RZ2, not counting any battle-axe handle. In RZ1, subdivision is also permitted where each new block contains a lawfully constructed dwelling.

There are two ways to divide a residential block in the ACT. Block subdivision creates new blocks, each with its own Crown lease. Unit titling keeps one Crown lease and registers a units plan over it, once the homes are built. This guide explains both, the rules for RZ1 and RZ2 under the Territory Plan 2023, where the Missing Middle reforms are up to, and the lease steps that are peculiar to the ACT. Figures are as at November 2026.

Block size rules at a glance (as at November 2026)

Zone Minimum block size or key rule Notes
RZ1 Suburban 350 m² for each new block Subdivision is also permitted where each new block contains a lawfully constructed dwelling (F01 Assessment Requirement 11)
RZ1 Suburban, unit titling All dwellings lawfully constructed; a standard block must be at least 600 m² Also permitted on a non-standard block (F01 Assessment Requirement 12)
RZ2 Suburban Density 300 m² for each new block Formerly named RZ2 Suburban Core
RZ3 Residential Transition 275 m² for each new block
RZ4 Urban Residential 250 m² for each new block
RZ5 Urban Density 250 m² for each new block
All new residential blocks Minimum depth and width by block size: 17 m and 6 m (compact), 25 m and 10 m (mid sized), 28 m and 14 m (large) Compact blocks must have a slope no greater than 10%

Block sizes and dimensions are from the Planning (Subdivision) Technical Specifications 2026 (NI2026-304), which commenced on 1 July 2026. The specifications say minimum areas "exclude any battle axe handle i.e., an access handle is not measured as part of the minimum area compliance." The unit titling and dwelling rules are from the Territory Plan's F01 Subdivision Policy. Zone names are from the E01 Residential Zones Policy, effective 1 July 2026.

Subdivision or unit titling: how it works in the ACT

In the ACT, subdivision is governed by the Territory Plan 2023 and the Planning Act 2023. ACT Planning says "The Territory Plan guides planning and development in the ACT", and that the final Territory Plan "came into effect in the ACT on 27 September 2024", replacing an interim plan in effect from November 2023.

Under the Planning Act 2023, "subdivision" includes surrendering leases and granting new leases to subdivide the land, and also subdividing land under the Unit Titles Act 2001. In practice, the two routes look like this:

  • Block subdivision. The Crown lease is varied so the land is divided into 2 or more blocks, each with its own lease. The F01 Subdivision Policy permits this in RZ1 where each new block is at least 350 m², or each new block contains a lawfully constructed dwelling. ACT Planning's Missing Middle snapshot puts it plainly: "Subdivision can now occur without first building a dwelling, provided minimum block sizes are met."
  • Unit titling. The homes are built on one block and a units plan is registered over the single Crown lease. In RZ1, F01 permits unit titling of multi-unit housing only where all dwellings have been lawfully constructed and, on a standard block, the block is at least 600 m². The Territory Plan Dictionary defines a standard block, broadly, as one originally leased or used for one or two dwellings, or a consolidation that includes such a block, with exceptions. Check the Dictionary for the full wording.

For how title types compare across Australia, see green title vs strata title.

Dual occupancy subdivision in Canberra

The Territory Plan defines dual occupancy housing as the use of land originally used or leased for single dwelling housing for two dwellings. If you are thinking about a dual occupancy, the choice of route matters:

  • Separate blocks first. If each new RZ1 block can meet 350 m² and the minimum block dimensions, you can apply to subdivide before building.
  • Build, then subdivide. F01 Assessment Requirement 11 also permits RZ1 subdivision where each new block contains a lawfully constructed dwelling. The technical specifications still apply as guidance.
  • Build, then unit title. Both homes stay on one Crown lease. In RZ1 this needs all dwellings built and, on a standard block, at least 600 m².

A secondary residence (granny flat) is different. F01 says separate title, including unit title, is not permitted for a secondary residence in any zone, and E01 caps a secondary residence at 90 m². For the wider picture, see can you subdivide a dual occupancy.

RZ1 Suburban and RZ2 Suburban Density

E01 describes the RZ1 policy outcome as "a range of housing choices in a suburban setting which is primarily low density and low rise", and RZ2 as "a mix of low and medium density housing". Both zones list subdivision as a permissible use, which means it needs development approval unless exempt.

The two zones differ mainly in density and height:

  • RZ1: 350 m² minimum for new blocks, 2 storeys.
  • RZ2: 300 m² minimum for new blocks, 2 storeys for single dwellings and secondary residences, 3 storeys for multi-unit housing.
  • Both: site coverage for multi-unit housing is 45% of the original block area.

In every residential zone, F01 Assessment Requirement 8 also asks whether a new dwelling can be accommodated on the block under the Territory Plan, or, where one dwelling is already built, whether any building on a new lease is, or can be designed, in line with the Plan. That is often where the existing house decides the layout.

Battle-axe blocks

Battle-axe blocks remain possible, but the technical specifications limit their driveways. They must not result in more than 2 driveways to the original block, the removal of street trees, or more than 11 metres of continuous driveway width at the kerb. ACT Planning's snapshot says the new specifications "discourage battle-axe block layouts". The specifications are a guide rather than an absolute bar: F01 says the Authority may approve an application that does not satisfy them "where satisfied the development proposal meets all relevant assessment outcomes."

The Missing Middle reforms: what is in force and what is not

Change Status as at 12 November 2026
Territory Plan: Planning (Missing Middle Housing Reform) Major Plan Amendment 2026 (NI2026-246, MPA-04) In force. Approved by the Minister on 22 May 2026. Commenced on 1 July 2026 under Commencement Notice CN2026-5
Planning (Subdivision) Technical Specifications 2026 (NI2026-304) In force from 1 July 2026
50% lease variation charge reduction for RZ1 and RZ2 Available from 1 July 2026, subject to conditions
Planning (Missing Middle Housing) Amendment Act 2026 (A2026-17) In force. Introduced as a Bill 24 March 2026, passed 21 October 2026, notified 9 November 2026. Main provisions commenced 10 November 2026

The Territory Plan amendment. MPA-04 replaced the Residential Zones Policy and changed the Subdivision Policy. It also renamed the residential zones: the amendment describes its subject land as "RZ1 Suburban and RZ2 Suburban Core", and the replacement E01 names RZ2 the "Suburban Density Zone". Some ACT Government material still uses the old name. ACT Planning says missing middle housing is now permitted across RZ1 and RZ2, with low-rise apartments of up to two storeys in RZ1 and three storeys in RZ2. For the background, see ACT Missing Middle reforms: RZ1 blocks can now be subdivided to 350 m².

The Amendment Act (in force from 10 November 2026). The Act amends the Planning Act 2023. Its main changes:

  • Small subdivisions and consolidations of typical residential blocks are no longer significant development. A new section 42A limits a subdivision development proposal to one that both creates or consolidates blocks and creates or removes roads, and only those stay in that category. The revised explanatory statement says the others get one period of public notification and "the 30-45 working day DA decision timeframe".
  • Section 276 now allows a secondary residence on a residential lease limited to a single dwelling, without a lease variation.
  • A new exempt declaration pathway for some lease variations, such as changing the maximum number of dwellings. The Authority must decide within 10 working days, and a declaration expires 3 years after it is made.

See ACT passes faster approvals for small subdivisions.

Who approves a subdivision in Canberra

The Territory Planning Authority decides development applications (DAs) under the Planning Act 2023. Under section 43 of the Planning Act 2023, a DA for a subdivision development proposal is a subdivision design application, and it must include a detailed plan consistent with the Territory Plan. Since 10 November 2026, a subdivision development proposal is one that both creates or consolidates blocks and creates or removes roads (section 42A). Before then, the definition also covered proposals that only created or consolidated blocks, but it excluded block-boundary changes and subdivision under the Unit Titles Act 2001.

A proposal that needs a subdivision design application is significant development (section 94). Since 10 November 2026 that covers only subdivisions that also create or remove roads, so a typical residential block split is no longer significant development (unless it needs an environmental impact statement or design review panel consultation). ACT Planning publishes a 60 working day decision timeframe for significant development, with two notification stages of 20 and 10 working days. For other development the explanatory statement gives 30 to 45 working days, and ACT Planning gives a 15 working day public notification period.

You may also see the term estate development plan. Transport Canberra and City Services' page still describes these by reference to section 94 of the Planning and Development Act 2007, for example where a subdivision's infrastructure is to be handed back to the Territory. Under the Planning Act 2023, the application for a proposal to create blocks and roads is a subdivision design application.

Unit titling follows a separate process. A licensed unit title assessor prepares a unit title assessment report, which "cannot be more than 3 months old" when the application is made, and collects the certificate of occupancy and use. The Environment, Planning and Sustainable Development Directorate then determines whether the application meets the Unit Titles Act 2001.

Registration. Access Canberra explains that documents are lodged with the ACT Land Titles Office for recognition on the ACT Land Titles Register, the official record of who owns property in the ACT. A block subdivision ends with new Crown leases and a deposited plan, and unit titling with a registered units plan.

Your team. Boundary work in the ACT must be done by a registered surveyor, registered under the Surveyors Act 2007 through the ACT Registrar of Surveyors. A town planner can advise on the Territory Plan and the DA.

For the step-by-step process and fees, see how to subdivide land in the ACT.

Crown leases and the lease variation charge

Crown leasehold. ACT Planning says "Leasehold is ACT's system of land tenure" and "A residential lease is usually for a term of 99 years". Land and buildings can only be used for a purpose authorised by the lease. Subdividing a block into 2 or more blocks is a variation of the Crown lease, and "To vary a Crown lease, you need development approval."

The lease variation charge (LVC). The Commissioner for ACT Revenue is legally responsible for the charge, the Authority administers it, and a delegate of the Commissioner determines it. ACT Planning says the final amount "is not determined until a DA is approved", after which you receive a Notice of Assessment. Standard variations use codified charges set in a determination; non-standard variations need a valuation.

Under the Planning (Lease Variation Charges) Determination 2026, for DAs submitted on or after 1 July 2026 and before 1 July 2027, and lodged before 1 April 2028:

  • Subdividing into 2 or 3 leases: $7,500 for each additional lease.
  • Subdividing into 4 or more leases: $7,500 for each of the first 2 additional leases and $5,000 for each further additional lease.
  • Increasing the number of dwellings: where a variation increases the number of dwellings permitted under a residential lease in a listed suburb, Schedule 2 applies: increased number of dwellings × the suburb's additional dwelling amount. For a total of 2 dwellings, that amount is, for example, $65,000 in Kambah and $105,000 in Gungahlin.

The 50% reduction. The ACT Government offers a 50% reduction in the codified LVC if you vary a Crown lease in RZ1 or RZ2 to add 1 or more dwellings, defer the charge on or after 10 June 2026, receive development approval for the variation before 30 June 2029, and complete all dwellings by 31 December 2030. The reduction is applied when you exit the LVC Deferred Payment Scheme.

How to find your block's zone and rules

  1. Look up the block on ACTmapi. ACT Planning describes it as an online mapping tool for land zoning, bushfire prone areas, aerial photography and survey marks, and it includes Territory Plan and heritage map layers.
  2. Read the Territory Plan on the ACT Legislation Register. Check the E01 Residential Zones Policy for your zone, the F01 Subdivision Policy for the subdivision and unit titling rules, and the Dictionary for terms such as standard block.
  3. Read the Planning (Subdivision) Technical Specifications 2026 for minimum block sizes, dimensions and battle-axe driveways.
  4. Get your Crown lease. Access Canberra's ACT Land Information System (ACTLIS) gives access to Crown leases, deposited plans and units plans. A fee applies to land title searches.

To compare the ACT with the states, see minimum lot size for subdivision in every Australian state.

Other things that decide whether a block can be split

  • Utilities. F01 permits subdivision only "where each of the subdivided blocks have utilities infrastructure."
  • Heritage. For a heritage-registered block, subdivision must not be prohibited by a guideline, order or agreement under the Heritage Act 2004, and must not otherwise diminish the place's heritage significance.
  • Bushfire. Under F01, blocks in a bushfire prone area are not developed where the bushfire attack level for later buildings is greater than BAL 29.
  • The existing house. It has to sit on its new block in line with the Territory Plan.

Check your own block

A Subdivision Checker report applies these rules to one address: planning and zoning, heritage, environment, contamination, bushfire, flood, servicing and access, measured lot geometry and concept subdivision design options, plus indicative cost ranges labelled as estimates. It is a starting point, not a substitute for advice from a registered surveyor or town planner. To see how the checks are set out, view our sample report, or order a report for your address.

Frequently asked questions

Can I subdivide my block in Canberra?

Subdivision is a permissible use in the RZ1 Suburban and RZ2 Suburban Density zones, but every proposal needs development approval from the Territory Planning Authority. In RZ1, each new block must be at least 350 m² or already contain a lawfully constructed dwelling. Block dimensions, utilities, heritage, bushfire and your Crown lease must also work.

What is the minimum block size for subdivision in RZ1?

Under the Planning (Subdivision) Technical Specifications 2026, in force from 1 July 2026, each new RZ1 block needs at least 350 m², not counting any battle-axe handle. RZ2 needs 300 m², RZ3 275 m², and RZ4 and RZ5 250 m². The Authority may approve a proposal that does not meet the specifications if it meets all relevant assessment outcomes.

How do I subdivide a dual occupancy in Canberra?

There are two routes. Block subdivision creates separate blocks, each with its own Crown lease, and in RZ1 each block must be at least 350 m² or contain a lawfully constructed dwelling. Unit titling keeps one Crown lease and registers a units plan over it. In RZ1 every dwelling must be lawfully built first, and a standard block must be at least 600 m².

Are the ACT Missing Middle reforms in force?

Yes. The Territory Plan changes, Major Plan Amendment 04, commenced on 1 July 2026. The Planning (Missing Middle Housing) Amendment Act 2026 (A2026-17) passed the Legislative Assembly on 21 October 2026, was notified on 9 November 2026, and its main provisions commenced on 10 November 2026.

Is there a lease variation charge to subdivide in the ACT?

Yes, a codified charge is set for subdividing a Crown lease. For development applications submitted on or after 1 July 2026 and before 1 July 2027, splitting a lease into two or three leases costs $7,500 for each additional lease. A suburb-based charge can also apply where the variation increases the number of dwellings permitted under the lease.

Sources

This guide is general information only, current at November 2026. Rules, charges and maps change, and every block is different. Speak to a registered surveyor or town planner about your property.

More subdivision guides

See what applies to your block.

A Subdivision Checker report works through the lot size test, constraints, approval pathway and costs for your address, with every source listed. Full report $199, or a $39 Snapshot.