Guides

Minimum lot size for subdivision in NSW and Sydney

Where NSW minimum lot sizes come from, the state rules for subdividing dual occupancies, figures from six council LEPs, and the other tests a block must pass.

Updated 14 min read

Want the answer for your address? Your report checks the zoning, lot size, constraints and costs for your block, in your inbox within 1–2 hours.

Check my block

New South Wales has no single statewide minimum lot size for subdivision. Each council's Local Environmental Plan (LEP) sets the minimum for new lots on its Lot Size Map, under clause 4.1, and other clauses in the same LEP can lower or raise it for particular zones or housing types. Frontage, lot width and battle-axe rules usually sit in the council's Development Control Plan (DCP).

On top of the LEP, two state policies can change the answer for a dual occupancy: the low and mid rise housing rules in the Housing SEPP, and the Low Rise Housing Diversity Code in the Codes SEPP. This guide explains both, compares six councils, and sets out the other tests a block has to pass. Figures are as at November 2026.

How the LEP sets the minimum

Clause 4.1 of a standard LEP says the size of any lot resulting from a subdivision is not to be less than the minimum size shown on the Lot Size Map for that land. Blacktown LEP 2015, for example, says exactly that. The map figure varies across a council area, so two R2 blocks in the same council can have different minimums.

The map is only the starting point. Many LEPs add clauses, numbered 4.1A, 4.1B and so on, that set dual occupancy lot sizes, allow smaller lots in some cases, or exclude a battle-axe access handle from the lot area. Read the whole of Part 4 of your LEP, not just the map.

State rules that change the minimum

Low and mid rise housing areas (Housing SEPP)

The NSW Government's Low and Mid-Rise Housing Policy started in two stages. Stage 1, from 1 July 2024, permitted dual occupancies and semi-detached homes in R2 Low Density Residential zones across NSW. Stage 2 started on 28 February 2025, when a new Chapter 6 was added to the State Environmental Planning Policy (Housing) 2021. The R2 dual occupancy permission now sits in section 166 of that chapter, so it does not apply on land the chapter excludes, such as bush fire prone land and heritage items.

Chapter 6 applies to a low and mid rise housing area: land within 800 m walking distance of a "Town Centre" on the Town Centres Map, or of a public entrance to a railway, metro or light rail station listed in the SEPP. NSW Planning says these areas are in Greater Sydney, the Central Coast, the Lower Hunter and Newcastle, and Illawarra-Shoalhaven.

In those areas, the current Housing SEPP sets these standards:

Housing SEPP, Chapter 6 Standard
Dual occupancy (s 168, zones R1, R2, R3 and R4) Lot at least 450 m², at least 12 m wide at the front building line
Subdividing a dual occupancy (s 169, zones R1, R2 and R3) Each lot at least 225 m² and at least 6 m wide at the front building line
Other conditions for that subdivision One dwelling per lot, lawful access and frontage to a public road, no battle-axe lots, Torrens title only (not strata)
Who it applies to Dual occupancies approved on or after 28 February 2025, or applied for on or after that date as a combined subdivision and dual occupancy application

Section 169(1A) says consent may be granted to this subdivision despite the provisions of another environmental planning instrument, such as a council LEP. NSW Planning's summary also gives 165 m² and 6 m per lot for subdividing terraces in R1, R2 and R3.

Chapter 6 does not apply everywhere. The exclusions include bush fire prone land, heritage items, some flood-affected land, land within 200 m of certain pipelines, land inside higher aircraft noise contours, and the Bathurst Regional, Blue Mountains, Hawkesbury and Wollondilly council areas. Check section 164 of the Housing SEPP for the full list.

Low Rise Housing Diversity Code (Codes SEPP)

The Low Rise Housing Diversity Code, in Part 3B of the State Environmental Planning Policy (Exempt and Complying Development Codes) 2008, lets 1 or 2 storey dual occupancies, manor houses and terraces be approved as complying development. It applies only where these homes are permitted with consent under a planning instrument that applies to the land, such as the council's LEP. For a dual occupancy:

  • The lot must be in Zone RU5, R1, R2 or R3 and have lawful access to a public road (clause 3B.1).
  • The parent lot must be at least 400 m², or the LEP's minimum lot area for dual occupancies if that is larger (clause 3B.8).
  • The lot must be at least 15 m wide at the building line, or 12 m where parking is reached only from a secondary road, parallel road or lane (clause 3B.8).

Part 6 of the Codes SEPP then allows Torrens title subdivision of a side-by-side dual occupancy with a complying development certificate under the code (clauses 6.3 and 6.4). Each resulting lot must:

  • be at least the minimum size the LEP specifies for subdividing land for a dual occupancy, or 200 m² if the LEP specifies none;
  • be at least 6 m wide at the building line, with lawful access and frontage to a public road;
  • have only one dwelling, and be in Zone RU5, R1, R2 or R3.

The dual occupancy must also be permissible with consent under the planning instrument that applies. For more on splitting a duplex, see can you subdivide a dual occupancy.

The October 2025 changes

On 31 October 2025 the NSW Government published an instrument that amended the Housing SEPP, the Codes SEPP and a number of council LEPs at once. Hornsby and Warringah are two of the LEPs it changed, and the new clauses are in the table and the Northern Beaches section below.

Minimum lot sizes in six councils (as at November 2026)

Council (LEP) R2 figures in the LEP What else applies
Blacktown (Blacktown LEP 2015) Dual occupancy: 500 m² attached, 600 m² detached (cl 4.1B) A detached dual occupancy can be split only if each of the 2 lots meets the Lot Size Map, or on a corner lot where each dwelling fronts a different road and each lot is at least 300 m² (cl 4.1C)
Parramatta (Parramatta LEP 2023) Dual occupancy: lot of at least 600 m² with at least a 15 m frontage to a public road (cl 4.1C) Subdividing a lot with a dual occupancy in R2, R3 or R4, so that each lot contains one of its dwellings, is not subject to the Lot Size Map minimum (cl 4.1(3B))
The Hills (The Hills LEP 2019) Dual occupancy: 600 m² attached, 700 m² detached (cl 4.1A) Subdividing a dual occupancy so each dwelling is on its own lot is not permitted, apart from some older approvals (cl 4.1C)
Hornsby (Hornsby LEP 2013) Lot Size Map minimums generally 500–600 m², per council. Dual occupancy: 700 m² attached, 800 m² detached; 800 m² and 900 m² in a heritage conservation area (cl 4.1C) Consent may be granted to subdivide an existing lawful dual occupancy into lots of at least 350 m² (attached) or 400 m² (detached), or 400 m² and 450 m² in a heritage conservation area, with the access handle excluded (cl 4.1D)
Central Coast (Central Coast LEP 2022) Dual occupancy: 550 m² attached, 700 m² detached (cl 4.1B) Consent may be granted to subdivide a dual occupancy in R1 or R2 into 2 lots that are both smaller than the Lot Size Map minimum (cl 4.1C)
Lake Macquarie (Lake Macquarie LEP 2014) 2-lot subdivision in R1 or R2: each lot at least 250 m² where a dwelling house or semi-detached dwelling could be appropriately located on it (cl 4.1A) Battle-axe lot in R2: 600 m², excluding the access handle. Corner lot in R2: 500 m² (cl 4.1C)

All LEP figures are from the current versions on the NSW legislation website, checked on 7 November 2026. The Hornsby range is from council's Subdivision page, which describes it as a general guide. Where a block is in a low and mid rise housing area in Zone R1, R2 or R3 and is not excluded from Chapter 6, consent may be granted under the Housing SEPP's 225 m² subdivision standard despite these LEPs, for dual occupancies approved or applied for on or after 28 February 2025.

Northern Beaches: in force now and the draft LEP

In the former Warringah area, Warringah LEP 2011 now requires an R2 lot of at least 800 m² for a dual occupancy (clause 4.1B, inserted in October 2025). Its clause 4.1C allows an existing lawful dual occupancy in R2 to be subdivided into lots of at least 400 m², with one dwelling each and any access handle excluded.

Council's draft Northern Beaches LEP would bring in one set of rules for the whole council area. As exhibited, it sets 800 m² for an attached and 900 m² for a detached dual occupancy in R2, and 400 m² per lot for subdividing a dual occupancy, with access corridors excluded. Submissions closed on 30 August 2026, and it is not in force. See Northern Beaches draft LEP.

Local rules by council

Each council's local environmental plan and development control plan set their own lot sizes and local controls. Our council guides set these out with the official sources:

How to find the minimum for your block

  1. Search your address on the NSW Planning Portal Spatial Viewer. Under Principal Planning Layers, turn on the Land Zoning Map and the Lot Size Map to see the zone and the minimum lot size shown for the land.
  2. Read your council's LEP on the NSW legislation website. Check Part 4 for clauses that vary the minimum, such as dual occupancy, battle-axe and corner lot rules.
  3. Check whether you are in a low and mid rise housing area, and whether any of the Housing SEPP's exclusions apply.
  4. Read the DCP for lot width, frontage and access handle rules.
  5. Get a section 10.7 planning certificate from council, which states the zoning, planning controls and hazards such as bush fire prone land that apply.

For how NSW compares with other states, see minimum lot size for subdivision in every Australian state.

Clause 4.6: when a lot falls short

Clause 4.6 of an LEP allows development consent even though a proposal would breach a development standard such as a minimum lot size. Taking Blacktown LEP 2015 as an example, the consent authority must be satisfied that the applicant has shown:

  • compliance with the standard is unreasonable or unnecessary in the circumstances, and
  • there are sufficient environmental planning grounds to justify the breach.

It does not help in every zone. In Blacktown's clause 4.6, consent cannot be granted for a subdivision in zones RU1, RU2, RU3, RU4, RU6, R5, C2, C3 or C4 if the subdivision would create 2 or more lots below the minimum, or any lot below 90% of it.

Complying development works differently. NSW Planning's guide describes it as a fast-track route for proposals that meet set development standards, with merit-based assessment through a development application as the alternative. In every case, a variation is a request, not an entitlement.

Other tests besides lot size

A block can meet the minimum and still not work as a subdivision. Other things that decide it include:

  • Frontage and width. Lot width rules mean a narrow block may not fit two lots side by side. The state dual occupancy rules above need 6 m per lot, and LEPs and DCPs set their own widths.
  • Battle-axe lots. Some LEPs exclude the access handle from the lot area, as Hornsby and Lake Macquarie do, and Hornsby's council page asks for an access handle at least 3.5 m wide for one to three lots. The Housing SEPP's 225 m² route does not allow battle-axe lots at all. See battle-axe subdivision explained.
  • Bush fire prone land. The NSW Rural Fire Service says subdivision of bush fire prone land for residential purposes needs a bush fire safety authority, and that residential subdivision is classified as integrated development. Bush fire prone land is also excluded from the low and mid rise housing rules. See subdividing bush fire prone land in NSW.
  • Flood, heritage and other overlays. Heritage items and some flood-affected land are excluded from Chapter 6 of the Housing SEPP, and heritage conservation areas carry larger minimums in Hornsby.
  • Servicing. Each lot needs water, sewer, stormwater and power. In Sydney Water's area, council or the certifier will tell you if you need a Section 73 Compliance Certificate for the subdivision.
  • Secondary dwellings. NSW Planning says a lot on which a secondary dwelling (granny flat) is built cannot be subdivided.
  • Easements and title. Easements and restrictions on the title can dictate where new boundaries go.

Who approves a subdivision in NSW

There are two main approval routes:

  • Development application (DA). For most subdivisions, including those relying on an LEP clause or the Housing SEPP's 225 m² standard, a DA is assessed by the council.
  • Complying development certificate (CDC). Where the Low Rise Housing Diversity Code and Part 6 of the Codes SEPP apply, a CDC can be issued by the council or a registered certifier. NSW Planning's guide says complying development can be assessed in 20 days.

After approval, a subdivision certificate certifies that the plan has been completed in line with the consent and authorises its registration. It is usually issued by the council, and in some cases by a registered certifier. The plan is then lodged with NSW Land Registry Services, usually electronically by a registered surveyor, and new titles are issued once it is registered.

For the full process, timeframes and fees, see how to subdivide land in New South Wales. For the 2026-27 fees added up for a two-lot split in Greater Sydney, see our Sydney and NSW subdivision cost guide.

Check your own block

A Subdivision Checker report applies these rules to one address: planning and zoning, including the minimum lot size rules that apply, heritage, environment, contamination, bushfire, flood, servicing and access, measured lot geometry and concept subdivision design options, plus indicative cost ranges labelled as estimates. It is a starting point, not a substitute for advice from a registered surveyor or town planner. To see how the checks are set out, view our sample report, or order a report for your address.

Frequently asked questions

What is the minimum lot size for subdivision in NSW?

There is no single statewide minimum. Each council's Local Environmental Plan (LEP) sets the minimum on its Lot Size Map, and clauses in the LEP can vary it. Frontage and battle-axe rules usually sit in the council's Development Control Plan (DCP). State rules can also apply, such as the 225 m² minimum per lot for subdividing a new dual occupancy in a low and mid rise housing area.

What is the minimum lot size for subdividing a dual occupancy in NSW?

It depends on the pathway. In a low and mid rise housing area, the Housing SEPP sets 225 m² and 6 m width per lot in the R1, R2 and R3 zones, for dual occupancies approved or applied for on or after 28 February 2025. Under the Low Rise Housing Diversity Code, each lot must meet the LEP's dual occupancy subdivision minimum, or 200 m² if the LEP sets none. Elsewhere, the council's LEP decides.

What is the minimum lot size in Sydney?

Each Sydney council sets its own. For example, Hornsby Council says its R2 minimums generally range from 500 m² to 600 m², while Blacktown's LEP requires 500 m² for an attached dual occupancy and 600 m² for a detached one in R2. Check the Lot Size Map and clauses for your council's LEP.

Can I subdivide if my block is just under the minimum lot size?

Sometimes. Clause 4.6 of an LEP lets you ask the consent authority to vary a development standard such as a minimum lot size. You must show that compliance is unreasonable or unnecessary and that there are sufficient environmental planning grounds. It is not available for some subdivisions in rural, conservation and large lot residential zones, and it is not an entitlement.

How do I find the minimum lot size for my block in NSW?

Search your address on the NSW Planning Portal Spatial Viewer and turn on the Land Zoning Map and Lot Size Map layers. Then read your council's LEP on the NSW legislation website for clauses that vary the minimum, and the DCP for frontage and battle-axe rules. A section 10.7 planning certificate from council lists the zoning and planning controls for the land.

Sources

This guide is general information only, current at November 2026. Rules and maps change, and every block is different. Speak to a registered surveyor or town planner about your property.

More subdivision guides

See what applies to your block.

A Subdivision Checker report works through the lot size test, constraints, approval pathway and costs for your address, with every source listed. Full report $199, or a $39 Snapshot.