In the City of Melville, the lot size you need to subdivide comes from two places. The City's Local Planning Scheme No. 6 (LPS6) gives your lot a density code, such as R12.5, R20 or R40/60, and Table D of the state Residential Design Codes (R-Codes) sets the minimum and average site area for that code. The Western Australian Planning Commission (WAPC) makes the decision, not the City.
Melville then adds its own layer of rules. Split codes depend on vehicle access, Willagee has a 3,000 m² test, heritage-listed places need approval before demolition, activity centres run on their own plans, and a crossover policy controls new driveways. This guide sets out those local rules alongside the state figures. Figures are as at November 2026.
Which planning scheme applies in the City of Melville
The operative scheme is City of Melville Local Planning Scheme No. 6, gazetted on 27 May 2016. The current consolidated text published by the Department of Planning, Lands and Heritage includes Amendment 20, gazetted on 11 September 2026, which recoded a lot in Davies Crescent, Kardinya, from R40 to R60.
Under clause 25, the R-Code for land is "the coding number superimposed on a particular area" of the Scheme Map. LPS6 does not set its own residential minimum lot sizes; its local changes to the R-Codes sit in clause 26, covered below.
Scheme review under way. The City began reviewing LPS6 in 2021. Its latest consultation closed on 31 August 2026, and the City said a draft scheme was expected in "Late 2026", with the statutory process in 2027. LPS6 stays in force until a replacement is approved.
How to find your lot's R-Code
- IntraMaps. The City says "To check the particular zoning for a piece of land, use our online mapping system, intramaps." It shows zoning and R-Code information, and whether an activity centre plan applies.
- LPS6 scheme maps. The Department of Planning, Lands and Heritage publishes the scheme as eight locality maps. The Applecross and Mount Pleasant map, for example, shows codes from R12.5 and R15 up to R60, the split code R40/60, and R-AC0. The Melville and Myaree map adds R17.5 and split codes such as R20/60, R30/40 and R40/60.
- PlanWA. The department's statewide mapping tool covers local planning schemes and heritage information.
The City's planning team can confirm the code for a specific lot.
Lot sizes for common Melville codes
These figures are from Table D of the R-Codes Volume 1 (Version 3, 10 April 2026) for single houses and grouped dwellings.
| R-Code | Minimum site area (m²) | Average site area (m²) | Minimum lot area/rear battle-axe (m²)* | Minimum frontage (m)* |
|---|---|---|---|---|
| R12.5 | 700 | 800 | 762.5 | 17 |
| R15 | 580 | 666 | 655 | 12 |
| R17.5 | 500 | 571 | 587.5 | 12 |
| R20 | 350 | 450 | 450 | 10 |
| R25 | 300 | 350 | 425 | 8 |
| R30 | 260 | 300 | 410 | – |
| R40 | 180 | 220 | 380 | – |
| R60 | 120 | 150 | 120 | – |
*Table D applies these two columns to single houses only. A dash means not applicable.
A subdivision has to pass both the minimum and the average test. At R20, two lots of 350 m² pass the minimum, but the 450 m² average means two lots generally need at least 900 m² between them. At R12.5 the same test means about 1,600 m², which is why R12.5 streets are much harder to split than R20 streets. For the full table, the five per cent variation and how the battle-axe access leg is counted, see our guide to the minimum lot size for subdivision in WA and battle-axe subdivision explained.
Local rules that change the answer in Melville
Split codes: access, not just area
Several Melville maps show split codes, such as R20/60 or R40/60. Under clause 26(1) of LPS6, where the Scheme Map shows "two density codes in the form of a split R-Code", the City applies the lower code unless the access conditions in the clause are met:
- for a site with frontage to a primary or district distributor road, all vehicle access, including access for existing development, is provided to a road or carriageway other than the distributor road; and
- for a site that adjoins such a site but does not itself have that frontage, the City is satisfied that vehicle access is provided to the adjoining site "so as to obviate the need for direct access" to the distributor road.
So on a split-coded lot, the higher code turns on how vehicles get in and out, not just on lot size.
Willagee: the 3,000 m² test
Clause 26(2) applies to land coded R40/60 in Willagee. The lower code, R40, applies unless all of the following are met:
- the lot is at least 3,000 m²;
- the development or subdivision creates single or grouped dwellings only; and
- the lots created are not irregularly shaped and each has its own street frontage.
Most single house lots are well under 3,000 m², so a standard lot will usually be assessed at R40. The Willagee Structure Plan, covering the area bounded by North Lake Road, Stock Road, Leach Highway and Garling Street, also guides development there.
Restrictive covenants that limit dwelling numbers
Clause 35 of LPS6 says a restrictive covenant that limits the number of dwellings below what the scheme allows "is extinguished or varied" to that extent. The trade-off is that development approval is then needed for any dwelling beyond the number the covenant allowed, and the City cannot grant that approval unless it first gives notice of the application under clause 64 of the deemed provisions.
Heritage-listed places
The City's Local Heritage Survey and Heritage List 2019 (Version 3 adopted on 16 June 2020) records places of local heritage value. The Heritage List "forms part of the Local Planning Scheme", and for listed places the City says:
- all proposed works are subject to the Local Planning Scheme, including planning approval;
- "Demolition of a listed place constitutes development and is subject to the scrutiny and approval of Council"; and
- Council may require a heritage assessment, a heritage impact statement and an archival record, at the owner's expense.
If a subdivision layout depends on removing a listed house, that approval comes first.
Activity centres: Canning Bridge, Kardinya and others
Some land near centres is coded R-AC0 on the scheme maps, where an activity centre or structure plan guides development. IntraMaps shows whether one applies. The City lists plans for Canning Bridge, Kardinya, the Melville City Centre in Booragoon, the Melville District Activity Centre, Murdoch, Riseley and Willagee.
- Canning Bridge. The plan covers a precinct of roughly 800 m around Canning Bridge Station, across Melville and South Perth. The WAPC approved the original plan in April 2016. An updated version was conditionally approved by the WAPC's Statutory Planning Committee on 10 June 2026, and the City says "Until completion of this process the original CBACP remains in effect."
- Kardinya. Under the scheme's Kardinya provisions (Schedule B), the City may require a Local Development Plan to coordinate access and egress for residential lots abutting the South Street road reservation before it considers a development application or recommends on a subdivision.
Crossovers and street trees
New lots usually need a new driveway. The City's Crossover Policy (CP-110, last reviewed 16 July 2024), its crossovers web page and its crossover guidelines say:
- work cannot start until written approval is granted, and the City asks you to allow at least 10 business days; there are no application or inspection fees;
- the minimum crossover width is 3 m and the maximum 6 m, or 4.5 m where the frontage is 12.5 m or less;
- a crossover must be at least 2.0 m from a street tree and 0.5 m from the side property line, including battle-axe driveways serving a subdivided block;
- obstructions are to be relocated "wherever possible at the property owner's cost", and paired aprons are recommended for narrow lots;
- the City pays a fixed subsidy of $495 for the first crossover to the land (claimed after construction), and "The total cost of construction of a second or any subsequent vehicle crossing shall be borne by the applicant."
This matters for battle-axe and side-by-side layouts that need a second driveway.
Land beside the Swan and Canning rivers
The Department of Biodiversity, Conservation and Attractions (DBCA) says it "has planning and development authority over the DCA, which includes private property", meaning the Swan Canning development control area. If your lot is next to the river foreshore, check whether any part of it is inside or affected by that area.
How subdivision approval works
You apply to the WAPC, not the City. The WAPC refers the proposal to the City and any affected public authority or utility, which have 42 days to respond with objections or recommendations. From 1 July 2026 the WAPC application fee for a freehold subdivision of two to 100 lots is $3,837 plus $85 per lot, and endorsement is $719 plus $8 per lot.
Water Corporation's standard infrastructure contributions for 1 July 2026 to 30 June 2027 are $2,756 for water and $5,121 for wastewater per lot, plus $41 for drainage in urban declared drainage areas (not strata). They are not subject to GST. LPS6 does not list any development contribution areas. For the full process, see how to subdivide land in Western Australia, and for an estimate of total costs, try our subdivision cost calculator.
Check the DFES Map of Bush Fire Prone Areas as well. Designation can trigger State Planning Policy 3.7 where a proposal increases development intensity.
Draft R-Codes and scheme review (proposed, not in force)
The State Government released draft R-Codes on 24 October 2026. The Government's media statement says average lot sizes for R10 to R25 would be scrapped in Perth and Peel. That would affect the R12.5, R15, R17.5, R20 and R25 figures above if adopted. Submissions close at 5.00pm (AWST) on Friday 26 February 2027, and the department expects amendments to begin coming into effect later in 2027, subject to consultation and approval. Applications continue to be assessed under the current framework, so the Table D figures above apply for now.
Locally, the City says its LPS6 review is looking at where "moderate, targeted increases in residential density" may suit, mainly near the Canning Bridge, Booragoon and Riseley centres and along Canning Highway and Marmion Street. Any recoding would only take effect once a new scheme is approved.
Contacting the City of Melville
The City can be reached on 1300 635 845 or (08) 9364 0666 during business hours, or in person at the Civic Centre, 10 Almondbury Road, Booragoon, Monday to Friday, 8.30am to 5.00pm (excluding public holidays). The postal address is Locked Bag 1, Booragoon WA 6954.
Check your own block
A Subdivision Checker report applies these rules to one address: planning and zoning, heritage, environment, contamination, bushfire, flood, servicing and access, measured lot geometry and concept subdivision design options, plus indicative cost ranges labelled as estimates. It is a starting point, not a substitute for advice from a licensed surveyor or town planner. To see how the checks are set out, view our sample report, or order a report for your address.
Frequently asked questions
What is the minimum lot size for subdivision in the City of Melville?
It depends on the density code (R-Code) that Local Planning Scheme No. 6 gives your lot. Table D of the R-Codes Volume 1 then sets the minimum and average site area. At R20 the minimum is 350 m² and the average is 450 m², so two lots generally need at least 900 m². At R12.5, a code used in parts of Applecross and Mount Pleasant, it is 700 m² and 800 m², so two lots generally need at least 1,600 m². At R40 it is 180 m² and 220 m².
How do I find the R-Code for my property in Melville?
The City says to use its online mapping system, IntraMaps, which shows zoning and R-Code information and whether an activity centre plan applies. The Department of Planning, Lands and Heritage also publishes the Local Planning Scheme No. 6 maps as eight locality maps, and PlanWA covers local planning schemes statewide. The City's planning team can confirm the code for a specific lot.
What does a split code such as R20/60 mean in Melville?
Under clause 26(1) of Local Planning Scheme No. 6, where the scheme map shows two codes the City applies the lower code unless access conditions are met. For a site fronting a primary or district distributor road, all vehicle access, including for existing development, must be from another road or carriageway, and for a site next to one, the City must be satisfied that vehicle access is provided to that neighbouring site so it does not need direct access to the distributor road. In Willagee, R40/60 land stays at R40 unless the lot is at least 3,000 m² and other conditions are met.
Does the City of Melville approve subdivisions?
No. In Western Australia the Western Australian Planning Commission (WAPC) decides subdivision applications. The WAPC refers each application to the City and to agencies such as Water Corporation, which have 42 days to respond with objections or recommendations. The City and other agencies then confirm (clear) that their conditions have been met before the WAPC endorses the plan.
Can I subdivide a heritage-listed property in Melville?
It is not ruled out, but extra controls apply. The City's Heritage List forms part of its planning scheme, and the City says all proposed works on a listed place are subject to the scheme, including planning approval. Demolition of a listed place is development that needs Council approval, and the City may require a heritage assessment, a heritage impact statement and an archival record at the owner's expense. A licensed surveyor or town planner can advise on a specific lot.
Are lot sizes in Melville changing?
Changes are proposed but not in force. The draft R-Codes released on 24 October 2026 propose scrapping average lot sizes for R10 to R25 in Perth and Peel, with comment closing at 5.00pm (AWST) on Friday 26 February 2027. Separately, the City is reviewing Local Planning Scheme No. 6; the City said a draft scheme was expected in late 2026, with the statutory process in 2027. The City says no final decisions have been made.
Sources
- City of Melville Local Planning Scheme No. 6, scheme text (updated to Amendment 20, September 2026)
- City of Melville planning information: scheme text and maps (DPLH)
- City of Melville Local Planning Scheme No. 6, Map 02, Applecross and Mount Pleasant localities (DPLH)
- City of Melville Local Planning Scheme No. 6, Map 03, Melville and Myaree localities (DPLH)
- City of Melville: Local Planning Strategy and Scheme
- City of Melville: Online Maps and Zoning
- Melville Talks: Local Planning Scheme 6 Review
- City of Melville: Willagee Structure Plan
- City of Melville: Activity Centre and Structure Plans
- City of Melville: Canning Bridge Activity Centre Plan
- City of Melville Local Heritage Survey and Heritage List 2019
- City of Melville Crossover Policy (CP-110)
- City of Melville: Crossovers
- City of Melville Crossover Guidelines and Specifications
- City of Melville: Contact us
- Swan Canning development control area and maps (DBCA)
- Residential Design Codes Volume 1 (Version 3, 10 April 2026)
- WAPC Subdivision Applications and Fees Guide (version 10.7, July 2026)
- Flow chart of the subdivision process (WAPC)
- PlanWA (Department of Planning, Lands and Heritage)
- Water Corporation: Infrastructure contributions
- Bushfire prone areas (DFES)
- Residential Design Codes Review (Department of Planning, Lands and Heritage)
- Residential Design Codes Review (Have Your Say WA)
- Changes to cut red tape for new granny flat developments (WA Government media statement, 24 October 2026)
This guide is general information only, current at November 2026. Rules, fees and maps change, and every block is different. Speak to a licensed surveyor or town planner about your property.
