Guides

Subdivision in the City of Cockburn: lot sizes and local rules

How subdivision works in the City of Cockburn: the scheme that sets your R-Code, the R30 cap on vacant split-coded land, the lot size figures, development contributions, Jandakot Airport noise policy and the City's clearance conditions.

Updated 13 min read

Want the answer for your address? Your report checks the zoning, lot size, constraints and costs for your block, in your inbox within 1–2 hours.

Check my block

In the City of Cockburn, the lot size you need to subdivide comes from two places. The City's Town Planning Scheme No. 3 (TPS3) gives your lot a density code, such as R20, R30 or a split code like R30/40, and Table D of the state Residential Design Codes (R-Codes) sets the minimum and average site area for that code. The Western Australian Planning Commission (WAPC) makes the decision on green title and survey strata subdivisions, not the City.

Cockburn then adds its own layer of rules. Vacant land with a split code is tested at R30, new lots pay a community infrastructure contribution, land near Jandakot Airport falls under a state noise policy, and the City's clearance conditions cover access legs, retaining walls and demolition. This guide sets out those local rules alongside the state figures. Figures are as at November 2026.

Which planning scheme applies in the City of Cockburn

The operative scheme is City of Cockburn Town Planning Scheme No. 3, gazetted on 20 December 2002. The consolidated text published by the Department of Planning, Lands and Heritage is updated to include Amendment 179, gazetted on 29 September 2026. Clause 4.2.3 says the R-Code density for land is "determined by reference to the Residential Design Codes density number superimposed" on the Scheme Map, and clause 4.2.2 says residential development covered by the R-Codes must conform with them unless the scheme provides otherwise.

Draft Local Planning Scheme No. 13. The City's Local Planning Strategy was endorsed by the WAPC, subject to modifications, on 13 February 2024. The City says the strategy guides draft Local Planning Scheme No. 13, which would replace TPS3, and that the draft is being considered by the WAPC for endorsement for advertising. The same page said advertising was expected in 2025, so check with the City for the latest position. It is not in force, so TPS3 still applies.

How to find your lot's R-Code

  • TPS3 scheme maps. The Department of Planning, Lands and Heritage publishes the scheme as 23 locality maps. The Hamilton Hill locality map (No. 1 of 23), for example, shows single codes from R20 to R100 alongside split codes R30/40 and R30/40/60. The Spearwood map (No. 6 of 23) shows R30/40 in a number of places, as well as R35/80. The legend also marks Development Areas, Development Contribution Areas, heritage places and the Jandakot Airport area.
  • Cockburn Mapping Hub. The City's online map (formerly Intramaps) shows property information such as zoning, lot boundaries and lot size, plus constraints, heritage and environmental data.
  • PlanWA. The department's statewide mapping tool covers local planning schemes and heritage information.
  • Structure plans. In newer estates, also check the approved structure plan for your suburb. The City lists them by suburb and says they can show "housing density, land use classifications and buffer zones."

The City's planning team can confirm the code for a specific lot.

Lot sizes for common Cockburn codes

These figures are from Table D of the R-Codes Volume 1 (Version 3, 10 April 2026) for single houses and grouped dwellings.

R-Code Minimum site area (m²) Average site area (m²) Minimum lot area/rear battle-axe (m²)* Minimum frontage (m)*
R20 350 450 450 10
R25 300 350 425 8
R30 260 300 410 –
R40 180 220 380 –
R60 120 150 120 –

*Table D applies these two columns to single houses only. A dash means not applicable.

A subdivision has to pass both the minimum and the average test. At R20, two lots of 350 m² pass the minimum, but the 450 m² average means two lots generally need at least 900 m² between them. At R30, which matters for Cockburn's split-coded land, two lots generally need at least 600 m². For the full table, the five per cent variation and how the battle-axe access leg is counted, see our guide to the minimum lot size for subdivision in WA and battle-axe subdivision explained.

Local rules that change the answer in Cockburn

Split-coded land: subdivision capped at R30

Parts of Cockburn's established suburbs, including Spearwood and Hamilton Hill, carry a split code such as R30/40. Clause 4.4.4 of TPS3, headed "Medium Density Residential Development", sets out how the City treats it:

  • For subdivision in split-coded areas, "the Council may only support subdivision (in the absence of built development) up to a maximum density of R30".
  • For development, "the Council may support development up to the maximum density of the split code", where the application is consistent with Local Planning Policy 1.2.

So on an R30/40 lot, a vacant land split is tested against R30 (a 260 m² minimum and 300 m² average). The higher code is a discretion tied to a development proposal, not an entitlement. Local Planning Policy 1.2, the City's Residential Design Guidelines (version 14, adopted 12 May 2026), includes specific clauses on split-coded lots and retained dwellings.

Two grouped dwellings on R20 lots of 900 m² or more

Clause 4.4.1 lets the City permit "2 grouped dwellings on any lot with an area of 900m2 or greater" in R20 areas, varying "the minimum site area per dwelling and the minimum lot area/ rear battleaxe requirements". This is a development provision for grouped dwellings, applied to a building proposal rather than giving a green title lot split. A licensed surveyor or town planner can advise how it applies to a specific lot.

Development Areas and structure plans

TPS3 lists Development Areas in Table 9, including DA 22 Port Coogee, DA 28 Success – Bartram/Hammond Roads and DA 33 Cockburn Coast. Under clause 5.2.2.2, subdivision and development in a Development Area "is to generally be in accordance with any structure plan that applies to the land".

Development contributions: DCP 13 and local plans

Development Contribution Plan 13 (Community Infrastructure) funds regional, sub-regional and local community facilities. The City says it applies citywide to land being subdivided or developed for residential, rural residential or resource zone purposes, in addition to any local plan, but not to lots that have no subdivision or development potential. Under TPS3, "Contributions shall be calculated on the basis of the number of new lots and/or dwellings created", existing dwellings are exempt, and the plan operates until 30 June 2031.

The City's 2025/26 DCP 13 report (version 14, rates indexed on 23 October 2026) sets these examples per lot or dwelling:

Suburb DCP 13 rate per lot/dwelling
Coogee/North Coogee $7,311.02
Hamilton Hill $5,299.92
Munster (Lake Coogee) $8,270.65
Spearwood $6,368.83
Success $4,043.09

Rates are reviewed annually and indexed quarterly, and the City notes a proposed adjustment to DCP 13 is with the Minister for Planning. Under clause 5.3.13.2, one of the events that triggers liability is the WAPC endorsing its approval on the deposited or survey strata plan. Under clause 5.3.15.1, an unpaid contribution "is a charge on the owner's land". Some areas also have their own plan for local roads, drainage, open space or facilities, such as DCA 12 Packham North and DCA 15 Treeby/Jandakot. The City's Development Contributions Officer can confirm the amount for a specific lot.

Jandakot Airport

Jandakot Airport sits in the City, and the scheme map legend uses JA for the airport. Land around it is covered by State Planning Policy 5.3: Jandakot Airport Vicinity:

  • In the Core Area (inside the 20 ANEF contour), where land is already zoned for housing there should be no scheme changes that would increase housing density, including increases in density coding or reductions in minimum lot size. No further subdivision or strata subdivision is to take place where it would increase the number of dwellings that may be developed. The policy does not remove pre-existing development rights under the scheme, so subdivision consistent with the current zoning may be considered. Dwellings are classed as "Unacceptable", and a notification on title is required as a condition of subdivision or planning approval.
  • In the Frame Area (between the 20 ANEF contour and Roe Highway, Ranford Road, Warton Road, Armadale Road and Kwinana Freeway), there is a general presumption against rezoning land to allow residential density above one dwelling per two hectares. Unless it is consistent with the relevant zoning and/or density coding, no further subdivision or strata subdivision is to take place where it would increase the number of dwellings.

Latitude 32, water protection and heritage

  • Latitude 32, formerly the Hope Valley Wattleup Redevelopment Project, is an industrial redevelopment covering part of Wattleup and Munster (and Hope Valley in the City of Kwinana). The City says the WAPC is the responsible authority for subdivision there.
  • The Resource zone's objective is "To provide for the protection of the Perth Metropolitan underground water resource". Rural and Resource zoned land is covered by the scheme's separate Rural Uses provisions (clause 4.10), so check those provisions rather than relying on the residential figures above.
  • The City's Heritage List is drawn from its Local Heritage Survey, which rates places A to D. Only A and B places are on the List, which is protected under TPS3. The City's Strategic Planning team handles enquiries about the Heritage List.

Access legs, crossovers and clearance conditions

The City's Subdivision Clearance Information Sheet sets out its usual conditions:

  • Buildings and structures not shown for retention must be demolished and removed, including swimming pools and rubble, and a retained house must meet setback requirements to the new boundaries.
  • Retaining walls over 500 mm need development approval and a building permit before the subdivision works.
  • For three or more lots, the access way must be constructed and drained. For two lots, the owner can build the drained access way, or install soakwells and compacted road base and pay a bond based on a written quote plus a 25% contingency.
  • Notifications on title may be required. The sheet's example wording begins "This land may be affected by midge from nearby lakes."

The City's Crossovers Policy says "Individual lots are limited to one (1) crossover for every 30 metres of frontage". Where a second crossover is allowed, the combined width is limited to one third of the frontage or 9 metres, whichever is less. For an approved crossover that meets the City's specifications, the City contributes "a maximum of $500 for the first crossing only".

How subdivision approval works

You apply to the WAPC through its Planning Online portal, not to the City. The WAPC refers the application to the City and agencies such as Water Corporation and Western Power, and the City has 42 days to assess it and recommend conditions. The City itself approves built strata subdivisions. Approval is valid for three years for five lots or fewer. When the works are complete, you lodge a clearance application with the City, then apply to the WAPC to endorse the plan.

From 1 July 2026 the WAPC application fee for a freehold subdivision of two to 100 lots is $3,837 plus $85 per lot, and endorsement is $719 plus $8 per lot. Water Corporation's standard infrastructure contributions for 1 July 2026 to 30 June 2027 are $2,756 for water and $5,121 for wastewater per lot, plus $41 for drainage in urban declared drainage areas (not strata). They are not subject to GST. For the full process, see how to subdivide land in Western Australia, and for an estimate of total costs, try our subdivision cost calculator.

Check the DFES Map of Bush Fire Prone Areas as well. Designation can trigger State Planning Policy 3.7 where a proposal increases development intensity.

Draft R-Codes changes (proposed, not in force)

The State Government released draft R-Codes on 24 October 2026. The Government's media statement says average lot sizes for R10 to R25 would be scrapped in Perth and Peel. Submissions close at 5.00pm (AWST) on Friday 26 February 2027. Applications continue to be assessed under the current framework, so the Table D figures above apply for now.

Contacting the City of Cockburn

The City's Administration Centre is at 9 Coleville Crescent, Spearwood, open 8.30am to 4.30pm, Monday to Friday (excluding public holidays). Its phone number is (08) 9411 3444, and its postal address is PO Box 1215, Bibra Lake DC WA 6965. Its general email address is customer@cockburn.wa.gov.au, and the Development Contributions Officer can be reached through the main phone number.

Check your own block

A Subdivision Checker report applies these rules to one address: planning and zoning, heritage, environment, contamination, bushfire, flood, servicing and access, measured lot geometry and concept subdivision design options, plus indicative cost ranges labelled as estimates. It is a starting point, not a substitute for advice from a licensed surveyor or town planner. To see how the checks are set out, view our sample report, or order a report for your address.

Frequently asked questions

What is the minimum lot size for subdivision in the City of Cockburn?

It depends on the density code (R-Code) that Town Planning Scheme No. 3 gives your lot. Table D of the R-Codes Volume 1 then sets the minimum and average site area. At R20 the minimum is 350 m² and the average is 450 m², so two lots generally need at least 900 m². At R30 it is 260 m² and 300 m², and at R40 it is 180 m² and 220 m². On split-coded land, such as R30/40, the scheme limits subdivision of vacant land to R30.

My Cockburn lot is coded R30/40. Which code applies?

Under clause 4.4.4 of Town Planning Scheme No. 3, the Council may only support subdivision (in the absence of built development) up to a maximum density of R30. It may support development up to the higher split code if the application is consistent with Local Planning Policy 1.2, the City's Residential Design Guidelines. So a vacant subdivision is tested at R30, and the higher code depends on a development proposal.

Does the City of Cockburn approve subdivisions?

Not for green title or survey strata lots. In Western Australia the Western Australian Planning Commission (WAPC) decides those applications. The WAPC refers each application to the City, which has 42 days to assess it and recommend conditions. Once the works are done, the City issues a clearance letter and the WAPC endorses the plan. The City does approve built strata subdivisions.

What development contributions apply when subdividing in Cockburn?

Development Contribution Plan 13 (community infrastructure) applies citywide to residential, rural residential and resource zoned land being subdivided or developed. It is charged per new lot or dwelling, and existing dwellings are exempt. The City's rates indexed on 23 October 2026 range from $3,728.08 to $8,270.65 per lot or dwelling depending on the suburb, for example $5,299.92 in Hamilton Hill and $6,368.83 in Spearwood. Some areas also have a local contribution plan.

Can I subdivide near Jandakot Airport?

It depends on where the lot sits against the airport's noise contours. Under State Planning Policy 5.3, in the Core Area (inside the 20 ANEF contour), scheme changes that would increase housing density should not be made, and no further subdivision is to take place where it would increase the number of dwellings, although the policy does not remove pre-existing development rights under the scheme. In the surrounding Frame Area, unless it is consistent with the relevant zoning and/or density coding, no further subdivision is to take place where it would increase the number of dwellings. A licensed surveyor or town planner can advise on a specific lot.

Are lot sizes in Cockburn changing?

Changes are proposed but not in force. The draft R-Codes released on 24 October 2026 propose scrapping average lot sizes for R10 to R25 in Perth and Peel, with comment closing at 5.00pm (AWST) on Friday 26 February 2027. Separately, the City is preparing draft Local Planning Scheme No. 13 to replace Town Planning Scheme No. 3, which remains the operative scheme.

Sources

This guide is general information only, current at November 2026. Rules, fees and maps change, and every block is different. Speak to a licensed surveyor or town planner about your property.

More subdivision guides

See what applies to your block.

A Subdivision Checker report works through the lot size test, constraints, approval pathway and costs for your address, with every source listed. Full report $199, or a $39 Snapshot.