In the City of Gosnells, the lot size you need to subdivide comes from two places. The City's Local Planning Scheme No. 24 (LPS 24) gives your lot a density code, such as R17.5, R20 or R30, and Table D of the state Residential Design Codes (R-Codes) sets the minimum and average site area for that code. The Western Australian Planning Commission (WAPC) makes the decision, not the City.
LPS 24 is new, so older advice about Gosnells may refer to the previous scheme. This guide sets out what the new scheme says, including the corner lot rule, rural lot sizes, development contribution areas and the special control areas. Figures are as at November 2026.
Which planning scheme applies in the City of Gosnells
The operative scheme is City of Gosnells Local Planning Scheme No. 24, gazetted on 30 September 2025 after the Minister endorsed it on 8 September 2025. The City says LPS 24 applies to the whole City except the Maddington Kenwick Strategic Employment Area, which is still covered by Town Planning Scheme No. 6 (gazetted in 2002). The scheme text and maps are read with the deemed provisions in the Planning and Development (Local Planning Schemes) Regulations 2015.
Clause 25(3) of LPS 24 says the R-Code coding of land "is shown by the coding number superimposed on a particular area" within the boundaries shown on the Scheme Map.
How to find your lot's R-Code
- LPS 24 scheme maps. The Department of Planning, Lands and Heritage publishes the scheme as 22 locality maps. The Kenwick locality map, for example, shows codes from R17.5 and R20 up to R80 and R100, and its legend marks the special control areas described below.
- The City's online mapping system. The City's Local Planning Schemes page links to it for checking a property's zoning under LPS 24.
- PlanWA. The department's statewide mapping tool covers local planning schemes.
The City's planning team can confirm the code for a specific lot.
Lot sizes for common Gosnells codes
These figures are from Table D of the R-Codes Volume 1 (Version 3, 10 April 2026) for single houses and grouped dwellings.
| R-Code | Minimum site area (m²) | Average site area (m²) | Minimum lot area/rear battle-axe (m²)* | Minimum frontage (m)* |
|---|---|---|---|---|
| R17.5 | 500 | 571 | 587.5 | 12 |
| R20 | 350 | 450 | 450 | 10 |
| R25 | 300 | 350 | 425 | 8 |
| R30 | 260 | 300 | 410 | – |
| R40 | 180 | 220 | 380 | – |
| R60 | 120 | 150 | 120 | – |
*Table D applies these two columns to single houses only. A dash means not applicable.
A subdivision has to pass both the minimum and the average test. At R20, two lots of 350 m² pass the minimum, but the 450 m² average means two lots generally need at least 900 m² between them. At R17.5 the average is 571 m², so two lots generally need at least 1,142 m². For the full table, the five per cent variation and how the battle-axe access leg is counted, see our guide to the minimum lot size for subdivision in WA and battle-axe subdivision explained.
Local rules that change the answer in Gosnells
Corner lots: up to R30
Clause 26(2) of LPS 24 says that for land in the Residential zone coded R25 or below, the City "may support development and/or recommend support for subdivision to a maximum density of R30", provided:
- the lot is located on a corner;
- the proposal complies with the R30 provisions of the R-Codes Volume 1; and
- it meets any related local planning policy.
This is a discretion, not an entitlement, and the WAPC still decides the subdivision. At R30, Table D sets a 260 m² minimum and a 300 m² average, compared with 350 m² and 450 m² at R20. A licensed surveyor or town planner can advise whether a particular corner lot is likely to qualify.
Higher-density areas: a minimum of R60
Clause 26(1) says that where the scheme map codes an area R80 to R160, any development or subdivision "is to achieve a minimum density of R60". In those areas, a simple two-lot split of a large lot may not meet the scheme.
Rural and Rural Residential land: four-hectare lots
The scheme says "a minimum lot size of 4 hectares applies to Rural Residential and Rural zoned land shown as 'AR4' on the scheme map". More generally, the Rural Residential zone objectives refer to lot sizes in the range of one to four hectares. On the scheme maps this is labelled ASR4 (Additional Site Requirements, Rural and Rural Residential). Check your lot's zone and any ASR4 marking before assuming a rural block can be split.
Development contribution areas
Special Control Area 2 covers the City's Development Contribution Areas, including:
- Canning Vale;
- West Canning Vale;
- Southern River Precincts 1, 2 and 3;
- Central Maddington;
- Maddington Road Precinct A and part of Precinct B;
- Homestead Road; and
- Kenwick South.
If your lot is inside one of these areas, expect a cost contribution towards shared infrastructure and administration costs set out in that area's development contribution plan when you subdivide or develop. Ask the City for the current rate before you budget.
Perth Airport Buffer
Special Control Area 1, the Perth Airport Buffer, is the basis for implementing State Planning Policy 5.1 (Land Use Planning in the Vicinity of Perth Airport). Inside it:
- building types rated "conditionally acceptable" or "unacceptable" for the relevant noise exposure zone need development approval first; and
- the City must recommend a subdivision condition to the WAPC, or impose a development condition, requiring a notification on title about potential aircraft noise.
Martin Watercourse Catchment
Within Special Control Area 3, the Martin Watercourse Catchment, the scheme does not permit dwellings, on-site effluent disposal or outbuildings larger than 54 m². The aim is to protect the watercourse from erosion and land degradation. It applies only within the SCA3 boundary shown on the scheme map.
Quarry buffers
Special Control Area 4 sets a one-kilometre buffer around the two quarries in Orange Grove and Martin. Inside it, a single house needs development approval from the City, and the City may recommend a subdivision condition requiring a notification on title about dust, noise and vibration.
Heritage
The City keeps an LPS 24 Heritage List, published on its Local Planning Schemes page. If your property is on it, demolition or new development is likely to need development approval first, and heritage can shape the layout of any subdivision.
How subdivision approval works
You apply to the WAPC, not the City. The WAPC refers the proposal to the City and any affected public authority or utility, which have 42 days to respond with objections or recommendations. From 1 July 2026 the WAPC application fee for a freehold subdivision of two to 100 lots is $3,837 plus $85 per lot, and endorsement is $719 plus $8 per lot.
Water Corporation's standard infrastructure contributions for 1 July 2026 to 30 June 2027 are $2,756 for water and $5,121 for wastewater per lot, plus $41 for drainage in urban declared drainage areas (not strata). For the full process, see how to subdivide land in Western Australia, and for an estimate of total costs, try our subdivision cost calculator.
Check the DFES Map of Bush Fire Prone Areas as well, as parts of the City are designated. Designation can trigger State Planning Policy 3.7 where a proposal increases development intensity.
Draft R-Codes changes (proposed, not in force)
The State Government opened consultation on proposed changes to the R-Codes on 24 October 2026. The Government's media statement says average lot sizes for R10 to R25 would be scrapped in Perth and Peel. That would affect the R17.5, R20 and R25 figures above if adopted. Submissions close at 5.00pm (AWST) on Friday 26 February 2027. The changes are proposed only and not in force, so the current Table D figures above still apply.
Contacting the City of Gosnells
The City's administration centre is at 2120 Albany Highway, Gosnells. Its phone number is (08) 9397 3000 and its email is info@gosnells.wa.gov.au.
Check your own block
A Subdivision Checker report applies these rules to one address: planning and zoning, heritage, environment, contamination, bushfire, flood, servicing and access, measured lot geometry and concept subdivision design options, plus indicative cost ranges labelled as estimates. It is a starting point, not a substitute for advice from a licensed surveyor or town planner. To see how the checks are set out, view our sample report, or order a report for your address.
Frequently asked questions
What is the minimum lot size for subdivision in the City of Gosnells?
It depends on the density code (R-Code) that Local Planning Scheme No. 24 gives your lot. Table D of the R-Codes Volume 1 then sets the minimum and average site area. At R17.5 the minimum is 500 m² and the average is 571 m², so two lots generally need at least 1,142 m². At R20 it is 350 m² and 450 m², so two lots generally need at least 900 m². Rural and Rural Residential land subject to the AR4 requirement (labelled ASR4 on the scheme maps) has a four-hectare minimum lot size.
What scheme applies in the City of Gosnells now?
Local Planning Scheme No. 24 (LPS 24), gazetted on 30 September 2025. It applies to the whole City except the Maddington Kenwick Strategic Employment Area, which remains under Town Planning Scheme No. 6. The scheme text and maps are read with the deemed provisions in the Planning and Development (Local Planning Schemes) Regulations 2015.
Can a corner lot in Gosnells be subdivided at a higher density?
Possibly. Under clause 26(2) of LPS 24, for Residential zoned land coded R25 or below, the City may support development or recommend support for subdivision up to a maximum of R30 where the lot is on a corner, the proposal complies with the R30 provisions of the R-Codes, and it meets any related local planning policy. It is a discretion, not an entitlement. At R30, Table D sets a 260 m² minimum and a 300 m² average.
Does the City of Gosnells approve subdivisions?
No. In Western Australia the Western Australian Planning Commission (WAPC) decides subdivision applications. The WAPC refers each application to the City and to public authorities and utility providers for comment and recommended conditions. The WAPC endorses the final plan once it is satisfied the conditions have been met.
Do development contributions apply to subdivision in Gosnells?
In some areas, yes. LPS 24 sets out Development Contribution Areas, including Canning Vale, West Canning Vale, Southern River Precincts 1, 2 and 3, Central Maddington, Maddington Road, Homestead Road and Kenwick South. If your lot is inside one, a cost contribution usually applies when you subdivide or develop. The City can confirm the current rate.
Does the Perth Airport buffer affect subdivision in Gosnells?
It can. Special Control Area 1, the Perth Airport Buffer, implements State Planning Policy 5.1. For land inside it, the City must recommend a subdivision condition to the WAPC requiring a notification on title about potential aircraft noise. Some building types also need development approval, depending on the noise exposure zone.
Sources
- City of Gosnells Local Planning Scheme No. 24, scheme text (DPLH)
- City of Gosnells Local Planning Scheme No. 24, Scheme Map No. 4 of 22, Kenwick locality (DPLH)
- City of Gosnells: Local Planning Schemes
- City of Gosnells LPS 24 Heritage List
- Residential Design Codes Volume 1 (Version 3, 10 April 2026)
- WAPC Subdivision Applications and Fees Guide (version 10.7, July 2026)
- Flow chart of the subdivision process (WAPC)
- PlanWA (Department of Planning, Lands and Heritage)
- Water Corporation: Infrastructure contributions
- Bushfire prone areas (DFES)
- Changes to cut red tape for new granny flat developments (WA Government media statement, 24 October 2026)
- Residential Design Codes Review (Have Your Say WA)
This guide is general information only, current at November 2026. Rules, fees and maps change, and every block is different. Speak to a licensed surveyor or town planner about your property.
