A new lot is only useful if a car can get to it. Whether the new lot faces the street, sits on a corner or is reached by a battle-axe leg, it needs a driveway, and the part of that driveway between the road and the boundary needs approval from the road authority.
This guide explains how crossovers are approved in each state, the WA rules for battle-axe access legs, how close a driveway can be to a corner, and what usually happens to an old crossover.
What a crossover is
What is a crossover? A crossover, also called a vehicle crossing or driveway crossing, is the part of a driveway that runs across the verge or footpath from the road to your property boundary. It sits on council or road reserve land, so it needs the road authority's approval even when the rest of the driveway is on your lot.
In a subdivision, the crossover question comes up in three ways:
- the new lot needs a crossover of its own, or a shared driveway
- the existing crossover may be in the wrong place for the new layout
- the subdivision approval may set conditions on how the driveway is built
Do you need a permit?
Do I need a permit for a new driveway when I subdivide? Yes. In every state, the councils we checked require approval for the crossover from the road authority, usually the council. In NSW it is a section 138 approval under the Roads Act 1993, which is separate from the development consent. In Victoria councils issue a vehicle crossing permit, and in the ACT the approval comes from ACT Government City Services (City and Environment Directorate).
New South Wales
The NSW Planning Portal says section 138 consent is needed for works on a public road or footpath, including driving a vehicle across a kerb or footpath. Council is the consent authority for unclassified roads, and on some classified roads Transport for NSW may also need to approve. The approval is separate from a development application (DA) or complying development certificate (CDC). With a DA you usually apply after the DA is approved; with a CDC you apply before lodging it. The Hills Shire Council describes its vehicular crossing request as a form of section 138 approval.
Councils set their own rules on top of this. The Hills allows only one driveway per residential lot. Northern Beaches Council's standard driveway width is 3.0 metres, and on a corner block the driveway should begin at least 6 metres from the corner. Sutherland Shire Council's 2026/27 fee for driveway construction approval for a single residential dwelling, including a formwork inspection, is $485.00, or $805.00 for larger developments including dual occupancy.
Victoria
Darebin City Council says a vehicle crossing permit is required to remove, modify, relocate or build a new vehicle crossing. Monash's 2026/27 fee for a vehicle crossing permit on a road of 50 km/h or less, with less than 8.5 m² of work, is $160.60 plus a minimum security deposit of $2,000.
Queensland
Brisbane City Council says you need a permit to build or modify a residential driveway, and a single detached house can have one driveway. Its listed fee is $20.30 for self-assessment and $293.40 for full assessment.
Western Australia
Many WA councils draw on WALGA's Residential Crossover Guidelines. They suggest a crossover at least 3.0 m wide, no more than 3.0 m wide on a lot with a frontage of 12.5 m or less, and at least 0.5 m from the side boundary, including battle-axe driveways serving a subdivided block. Your council's own crossover specification is what applies.
The City of Stirling requires written permission for a crossover and, in general, permits only one crossover per street frontage. Some WA councils share the cost of a first crossover. Stirling's policy offers a subsidy of 50% of the cost of a standard 3 m wide crossover, and the City of Wanneroo offers a subsidy of 50% of the construction cost of a concrete or brick-paved crossover, up to a capped amount. Both apply to the first crossover only, and Wanneroo says a pre-existing subdivisional crossover is not eligible without a receipt and a statutory declaration.
South Australia
The City of Holdfast Bay says section 221 of the Local Government Act 1999 gives council control of works on roads, so owners must get approval before altering a driveway. Its application fee is $70, and owners bear all associated costs.
Tasmania, the ACT and the Northern Territory
- TAS: the City of Launceston says all new, replacement or altered driveway crossings need a council permit, with no application fee. Derwent Valley Council says a new or relocated crossing will require a planning permit, then a driveway crossover permit.
- ACT: ACT Government City Services (City and Environment Directorate) approves new and modified driveways. For a single dwelling the standard driveway is 3.0 m wide at the boundary and 5.0 m at the kerb, with up to 5.5 m at the kerb generally supported only for a double garage, and assessment takes at least 15 working days.
- NT: the City of Darwin requires a works permit approved by its Infrastructure Permits Officer before driveway work starts.
Battle-axe access legs in WA
How wide does a battle-axe driveway need to be in WA? The WAPC's Operational Policy 2.2 sets a minimum battle-axe access leg width of 4 m for R2 to R40 codes and 3.6 m for R50 and higher. Where two battle-axe legs adjoin, a reduced width for each may be accepted if the subdivider enters an agreement with the local government for reciprocal rights of access.
The same policy says arrangements with more than two access legs will not be accepted unless exceptional circumstances apply. It notes that driveways may be required to be constructed and drained as a condition of subdivision approval, and, where a corner lot relies on an average lot size variation, expects crossovers and driveways to be provided in line with AS 2890 and the R-Codes. Truncations may be required where the leg meets the lot and the street. Our battle-axe subdivision guide compares the rules in each state.
How close to a corner
How close to a corner can a new driveway be? It depends on the council. Brisbane City Council says a driveway can't be less than 10 metres from a minor intersection or 20 metres from a major intersection. Knox City Council in Victoria says a crossing must not be closer than 10 metres to a local road intersection, and the ACT asks for 6 m clear of the tangent point on a corner block.
This matters most on corner blocks, where the second street is often the obvious place for a new driveway. Our corner block guide explains truncations and sight lines.
The old crossover
A new layout can leave the existing crossover in the wrong place. Councils commonly ask for a redundant crossover to be removed and the kerb reinstated:
- Knox City Council's 2026 guidelines say redundant crossings must be removed and the kerb and channel reinstated at the owner's expense.
- The City of Stirling says redundant crossovers must be removed from the verge, the kerbing closed and the verge reinstated.
- The City of Holdfast Bay says any disused invert and crossover must be reinstated to kerbing, footpath and verge.
- Derwent Valley Council says it will require the old crossing to be removed and the kerb or roadway made good.
Getting advice
A licensed surveyor can show where each lot meets the street and where a crossover could go. A town planner or civil engineer can confirm the access rules and any conditions that would apply to your subdivision.
If you would like a first look at the measured frontages and design options for your own address, you can check your block with Subdivision Checker.
Sources
- Section 138 approvals (NSW Planning Portal)
- Driveway and footpath crossings (The Hills Shire Council)
- Driveway and vehicle crossings (Northern Beaches Council)
- 2026-2027 fees and charges (Sutherland Shire Council)
- Vehicle crossing permit (Darebin City Council)
- Engineering fees 2026-2027 (City of Monash)
- 2026 Crossover Guidelines (Knox City Council)
- Residential driveway permits (Brisbane City Council)
- Driveway technical standards (Brisbane City Council)
- Operational Policy 2.2 Residential Subdivision, 31 May 2024 (WA Planning Commission)
- Residential Crossover Guidelines 2017 (WALGA)
- Crossover Policy (City of Stirling)
- Crossover rebate information sheet (City of Wanneroo)
- Driveway crossover, section 221 application (City of Holdfast Bay)
- Driveway crossings (Derwent Valley Council)
- Driveways and crossovers (City of Launceston)
- Driveway applications (ACT Government City Services)
- Works permits (City of Darwin)
This guide is general information only. For advice on your property, speak with a licensed surveyor or town planner in your state.
